SiC粒子增强铸造Al基复合材料的研制

本文用真空烘烤封罐法对 SiC 粒子进行预处理,在固液两相区内搅拌添加,制造了铸造 Al 基复合材料。测试表明,该复合材料具有铸造性能好,力学性能高的优点,适用于采用压铸、石膏型精密铸造、金属型铸造等工艺方法成型的活塞、连杆等要求苛刻的零件。     

分离有机/有机混合物的PVA、CA系列膜及其渗透汽化性能研究(Ⅱ) 成膜条件对渗透汽化性能的影响

用溶剂完全蒸发法制备了PVA复合膜 .经对MTBE/MeOH混合物的分离实验得到了PVA复合膜的最佳成膜条件 ,即 :铸膜液中PVA、马来酸浓度分别为 7%、3% ,热处理温度130～ 15 0℃ .在 1%～ 2 %丙酮水溶液中浸泡处理 4～ 8h ,CTA中空纤维RO膜被改性成渗透汽化膜 .CTA中空纤维膜的分离性能优于其它醋酸纤维素系列膜 ,PVA/CA复合膜的性能优于PVA/PAN复合膜和CA/PAN复合膜     

Effect of the particle size ratio on the conductivity of conductor-insulator powder composites: Numerical simulation

A theoretical method for determining the percolation limit and effective conductivity of composites based on polydisperse mixtures of insulator and conductor powders is proposed. The effect of the particle size ratio between the insulator and conductor on the percolation limit and effective conductivity is studied. Numerical simulation of the microstructure, effective properties, and percolation limit in composites is discussed. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 31–40, 2007.     

Exact solution of elasto-plastic stresses in a metal-matrix composite beam of arbitrary orientation subjected to transverse loads

An analytical elasto-plastic stress analysis is presented for a metal-matrix composite beam of arbitrary orientation subjected to a single transverse force applied to the free end of the beam and a uniformly distributed load. The material is assumed to be perfectly plastic in the elasto-plastic solution. A composite consisting of stainless-steel-reinforced aluminum was produced for this work. Sample problems are given for various orientation angles. Elastic, elastoplastic and residual normal and shear stresses are calculated. The location of the elasto-plastic boundary of the beam is obtained according to the x coordinates of the beam.     

光纤智能复合材料

对光纤型智能复合材料的工作原理，性能特点和应用前景作了介绍，并讨论了制造成型的技术问题。     

Influence of water and accelerated aging on the shear fracture properties of glass/epoxy composite

The degradation of interlaminar shear strength and shear fracture toughness of glass/epoxy composites due to uptake of distilled water and sea water has been studied. The composites were immersed in water for up to eight months at temperatures up to 70 °C. Unreinforced matrix resin samples were also immersed for periods up to 2 years. Sea water was absorbed less rapidly than distilled water. Weight gains below 1% did not influence the shear strength while higher weight gains reduced shear strength up to 25%. The loss in apparent interlaminar shear strength was uniquely related to specimen weight gain. Mode II fracture toughness, G _IIc, also decreased with increasing immersion time after an initial incubation period, but the accelerated tests were found to reduce G _IIc less than the room temperature tests at comparable weight gains.     

复合材料边界元素法研究

边界元法是一种迅速发展的数值解法.本文研究了在复合材料层合板中运用平面二次边界元法的有关问题.首先,讨论了将层合板等效为一般正交各向异性单层板的方法;其次,给出了偏轴情况下的基本解,研究了直线型二次边界元偏轴影响系数的解析计算以及域内应力表达式;最后对算例进行了计算,所得结果与相应的解析解和有限元相符甚好.     

偶联剂对玻璃纤维/环氧基复合材料界面介电性能的影响研究

本文研究了五种偶联剂对玻璃纤维浸润性能和玻璃纤维/环氧基复合材料界面介电性能的影响。结果表明,玻璃纤维经偶联剂处理后,其浸润活化能降低,与环氧树脂基体间的相容性及化学反应活性得到改善;因此赋予了玻璃纤维与环氧基体间以良好的界面粘结性能,从而提高了玻璃纤维/环氧基复合材料界面的介电性能。其提高的幅度大小与偶联剂的极性及化学结构有关。     

填充HDPE复合材料基体结晶形态的控制因素

本文以HDPE/玻璃微珠和HDPE/CaCO₃体系为研究模型,通过扫描电镜、红外光谱、偏光显微、小角激光散射和材料力学性能实验等方法考察了这两种体系的界面粘结性、填料含量、粒径及试样成型冷却速率等与其材料性能及基体结晶形态变化间的关系。实验结果表明;在复合材料试样成型过程中,因基体树脂冷却收缩而产生的界面应力可干扰基体中球晶的生长环境,应变诱导填料颗粒周围基体树脂的结晶,促使其表面伸展链晶体结构的形成,并由此而明显改变了复合材料的耐热性;复合材料的界面粘结性是产生这种应变诱导作用,并控制异相结晶的关键。     

复合超细丙纶及应用

对国内外细旦丙纶的开发和发展进行了介绍，阐述了单丝纤度为０．１～０．５ｄｔｅｘ的复合超细丙纶的制造方法、原材料规格、复合剥离技术以及产品质量。重点讨论了复合超细丙纶及织物的舒适性、染色性和卫生性，应用于织造、服装领域。