Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.     

分析矩形光波导损耗的简易方法

利用有效折射率和修正的有效折射率方法对矩形光波导的损耗作了简单有效的分析，并且计算出了纵向传播系数和衰减系数的大小。     

沥青油毡瓦国内外标准对比分析

从范围、原材料要求、组分要求、物理力学性能等方面对比分析了我国现行油毡瓦标准与欧美标准的区别,提出了我国制订沥青油毡瓦国家标准的的原则。     

改性石英砂滤料强化过滤处理含藻水

采用改性石英硝滤料强化过滤处理含藻水的试验结果表明，与石英硝滤料相比，改性石英硝滤料对含藻水具有优良的处理效果；经混凝沉演后水中的余铝对藻类的去除有促进作用。     

峡口水库沥青混凝土面板的施工与试验

以灌溉、防洪为主的峡口水库大坝，为沥青混凝土面板堆石坝，为研究低温抗裂性能，对沥青混凝土面板破损取样，进行了配比和多种力学性能试验，并与原面板设计指标进行了对比。由于面板经受住了－20℃以下的低温考验，其所用沥青指标、破损取样试验结果，特别是冻断低温指标，对确定水工沥青混凝土低温抗裂检验标准有重要参考价值。     

从关联分析法看如何改善沥青抗老化性能

用灰色关联分析法研究了沥青抗老化性能与沥青化学组成之间的关联程度，结果表明，影响再生沥青性质的主要因素是沥青中的芳烃和胶质的含量。通过添加芳香组分能改善沥青四组分之间的配伍性，从而可以改善再生沥青的抗老化性能。并通过对再生剂进行富芳处理，验证了上述结论。     

影响道路沥青低温抗裂性能的因素

用弯曲梁流变仪、直接拉伸试验机对7种国内外油源沥青样品进行了低温抗裂性能的评价，从沥青的四组分、相对分子质量及其分布来分析其对沥青低温抗裂性能的影响，结果表明，沥青的相对分子质量分布宽，对沥青的低温抗裂性能有利。     

关于沥青针入度指数

介绍了沥青针入度指数(PI)的由来和计算、使用意义、局限性和分析。     

Reduced modified quadratures for quadratic membrane finite elements

Reduced integration is frequently used in evaluating the element stiffness matrix of quadratically interpolated finite elements. Typical examples are the serendipity (Q8) and Lagrangian (Q9) membrane finite elements, for which a reduced 2 × 2 Gauss–Legendre integration rule is frequently used, as opposed to full 3 × 3 Gauss–Legendre integration. This ‘softens’ these element, thereby increasing accuracy, albeit at the introduction of spurious zero energy modes on the element level. This is in general not considered problematic for the ‘hourglass’ mode common to Q8 and Q9 elements, since this spurious mode is non‐communicable. The remaining two zero energy modes occurring in the Q9 element are indeed communicable. However, in topology optimization for instance, conditions may arise where the non‐communicable spurious mode associated with the elements becomes activated. To effectively suppress these modes altogether in elements employing quadratic interpolation fields, two modified quadratures are employed herein. For the Q8 and Q9 membrane elements, the respective rules are a five and an eight point rule. As compared to fully integrated elements, the new rules enhance element accuracy due to the introduction of soft, higher‐order deformation modes. A number of standard test problems reveal that element accuracy remains comparable to that of the under‐integrated counterparts. Copyright © 2004 John Wiley & Sons, Ltd.     

Density Measurement of Liquid Ni-Ta Alloys by a Modified Sessile Drop Method

The density of liquid Ni- Ta alloys was measured by using a modified sessile drop method. It is found that the density of the liquid Ni- Ta alloys decreases with the increasing temperature, but increases with the increase of tantalum concentration in the alloys. The molar volume of liquid Ni- Ta binary alloys increases with the increase of temperature ancl tantalum concentration.