番禺30-1砂岩强水驱气藏储层非均质性研究

针对垂向非均质性严重且边底水能量强的番禺30-1气田面临的潜在开发问题，通过岩心分析及测井二次解释，对其夹层特征及储层非均质性等进行了研究，划分出19个流动单元并定量描述了各流动单元的特征参数，建立了该气田的精细地质模型。综合评价表明，新建的地质模型具有较高的精度，为该气藏合理开发提供了坚实的地质基础。     

基于PC机群的大地电磁Occam反演并行计算研究

Occam反演以其稳定收敛和不依赖于初始模型的特性被广泛应用于大地电磁数据的处理，但偏导数矩阵的计算和拉格朗日乘子的求取导致大量的模型正演，使得反演速度较低。为此，研究了用基于PC机群的并行计算来解决这一问题的方法。首先对Occam反演方法进行了阐述；然后，分析了反演方法中各计算耗费的时间，提出对约占计算量90％的偏导数和拉格朗日乘子进行并行计算的思想，即偏导数计算采用频点计算一级的大粒度并行，拉格朗日乘子扫描和一维搜索分别采用弘值计算一级的大粒度并行和频点计算一级的小粒度并行；给出了并行计算的实现方法，即在PC机群上，利用主一从编程模式实现Occam反演的整体并行计算。在计算中，采用任务组合方式，减少了通信量，较好地实现了负载均衡。在4节点PC机群上，对应于拉格朗日乘子的扫描和一维搜索方式，整体加速比分别达到3．36和2．83。     

Biotransformation of l‐menthol by twelve isolates of soil‐borne plant pathogenic fungi (Rhizoctonia solani) and classification of fungi

The microbial transformation of l‐menthol ( 1 ) was investigated by using 12 isolates of soil‐borne plant pathogenic fungi, Rhizoctonia solani (AG‐1‐IA Rs24, Joichi‐2, RRG97‐1; AG‐1‐IB TR22, R147, 110.4; AG‐1‐IC F‐1, F‐4, P‐1; AG‐1‐ID RCP‐1, RCP‐3, and RCP‐7) as a biocatalyst. Rhizoctonia solani F‐1, F‐4 and P‐1 showed 89.7–99.9% yields of converted product from 1 , RCP‐1, RCP‐3, and RCP‐7 26.0–26.9% and the other isolates 0.1–12.0%. In the cases of F‐1, F‐4 and P‐1, substrate 1 was converted to (?)‐(1S,3R,4S,6S)‐6‐hydroxymenthol ( 2 ), (?)‐(1S,3R,4S)‐1‐hydroxymenthol ( 3 ) and (+)‐(1S,3R,4R,6S)‐6,8‐dihydroxymenthol ( 4 ), which was a new compound. Substrate 1 was converted to 2 and/or 3 by RRG97‐1, 110.4, RCP‐1, RCP‐3 and RCP‐7. The structures of the metabolic products were elucidated on the basis of their spectral data. In addition, metabolic pathways of the biotransformation of 1 by Rhizoctonia solani are discussed. Finally, from the main component analysis and the differences in the yields of converted product from 1 , the 12 isolates of Rhizoctonia solani were divided into three groups based on an analysis of the metabolites. Copyright © 2003 Society of Chemical Industry     

癸二酸二甲酯与1,2,2,6,6-五甲基哌啶醇的酯交换反应

对癸二酸二甲酯与1,2,2,6,6-五甲基哌啶醇的酯交换反应进行了研究;分别考察了四异丙基钛酸酯、氨基锂、氧化二辛基锡3种催化剂的性能;采用氢核磁共振确定了产物的结构;考察了以四异丙基钛酸酯为催化剂时反应温度、反应时间、原料配比和催化剂用量对反应的影响。实验结果表明,四异丙基钛酸酯催化剂的催化效果最好;在癸二酸二甲酯与1,2,2,6,6-五甲基哌啶醇摩尔比1∶1.79、四异丙基钛酸酯催化剂的用量为反应物总质量的0.31%、反应温度180℃、反应时间6h的条件下,所得产物中单(1,2,2,6,6-五甲基-4-哌啶基)癸二酸甲酯(简称单酯)质量分数为23%和双(1,2,2,6,6-五甲基-4-哌啶基)癸二酸酯(简称双酯)质量分数为73%,单双酯质量比为1∶3.17,产物收率为93.3%。该方法可得到理想的单双酯比例及产物收率,具有很好的工业应用前景。     

WCDMA系统接口信令消息的描述与实现

WCDMA作为第三代移动通信系统的主流标准，能够提供多种类型的多媒体服务。为了实现各种用户平面数据的传输，系统会提前通过控制平面对所需的无线资源进行分配。由于配置过程是通过接口之间发送控制平面应用协议消息来实现的，因此能否正确有效地对信令消息进行编解码成为保证系统稳定工作的关键因素。3GPP标准中，ASN．1语言被用来描述接口信令消息。首先简要介绍了WCDMA系统结构以及主要接口协议，重点描述了ASN．1存在的意义及其编解码规则，最后给出了基于ASN．1的开发环境下应用层网络协议的开发流程。     

提高深井硬地层钻井速度技术难点及对策

乌龙1井地层为南方海相沉积,地层古老、岩石硬度大、研磨性强、可钻性差、地层倾角大(最大为80°)井斜难以控制、蹩跳钻严重,制约了该地区深井钻井速度。文章介绍了解决提高钻井速度这一瓶颈问题,从深井优快钻井及其配套技术、硬地层钻进的钻头优选、优化钻井参数、引用新技术、新工艺、新工具等方面进行了探索,钻井速度有了大幅度地提高,对类似井具有一定的借鉴作用。     

基于C6711处理器cdma2000 1X系统前向信道信号的处理

在cdma20001x前向信道中,要对一段信号进行传送,一般选用QPSK调制,因为QPSK调制比QAM更适合噪音环境。采用TI6000系列的TMS320C6711芯片处理前向信道信号,可以对复杂性和实时性较高的信号做采集、量化、编码、调制等实时处理,主要功能通过软件编程实现,从而使系统具有结构灵活、可靠性高、可扩展等优点。     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Cu-Mg/Al_2O_3催化乙醇和乙二胺合成N-乙基乙二胺

在固定床反应器内,乙醇和乙二胺经分子间催化胺化反应合成了N-乙基乙二胺(NEED),考察了一系列铜系催化剂的活性,并筛选出催化性能较好的Cu-Mg/A l2O3催化剂;通过X射线衍射和透射扫描电子显微镜方法表征了助剂Mg对Cu/A l2O3催化剂的改性作用;考察了助催化剂Mg含量、反应温度、反应压力、进料量和乙二胺含量等对Cu-Mg/A l2O3催化剂性能的影响。实验结果表明,Cu-Mg/A l2O3催化剂具有很好的活性和选择性;在200℃、3.0MPa、质量分数20%的乙二胺乙醇溶液、进料量1.0mL/m in的条件下,乙二胺的转化率为71.56%,产物NEED的选择性和收率分别为92.62%和69.86%;经过20 d的连续使用表明,Cu-Mg/A l2O3催化剂具有良好的稳定性。     

Synchronous Full-Scan for Asynchronous Handshake Circuits

Handshake circuits form a special class of asynchronous circuits that has enabled the industrial exploitation of the asynchronous potential such as low power, low electromagnetic emission, and increased cryptographic security. In this paper we present a test solution for handshake circuits that brings synchronous test-quality to asynchronous circuits. We add a synchronous mode of operation to handshake circuits that allows full controllability and observability during test. This technique is demonstrated on some industrial examples and gives over 99% stuck-at fault coverage, using test-pattern generators developed for synchronous circuits. The paper describes how such a full-scan mode can be achieved, including an approach to minimize the number of dummy latches in case latches are used in the data path of the handshake circuit.