Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.     

传统机械加工表面形貌评定的缺陷及发展方向

本文通过对传统机械加工表面形貌评定体系的分析，指出其不能完整地、从本质上反映表面的特征。并提出轮廓长度率、表面真面积率、表面分形维数D、比例系数K四个评定参数，通过分析可以看出这组参数比传统方法所具有的优越性和代替传统方法的可能性。     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

孔径法测量铜带残余应力的试验研究

介绍了用于薄板残余应力测量的新方法——孔径法,该方法是通过测量冲孔直径的变化来间接求出各方向的残余应力;文中详细阐述了残余应力的标定方法;由于可针对不同材料建立了被测材料的平均应力(σ_l)与被测板材宽度(B)、厚度(H)以及冲孔后直径变化率(△D_i/D)之间的数学模型,因而使薄板残余应力测量变得简便而经济;此外还对该方法的分辨率与测量精度进行了实验、计算与分析。     

Rene′95粉末合金喷丸强化研究

研究了Ｒｅｎｅ′９５热等静压粉末高温合金喷丸后的残余应力场、组织结构、致密度及其与疲劳性能的关系。结果指出，喷丸强化能够有效地提高合金高周和低周疲劳强度。     

垂直平行束状孔爆破模型试验与分析

垂直平行密集束状孔落矿有底柱崩落法是一种新的采矿方法。通过爆破模型试验，测试爆破应力，观察分析爆破效果，探求最佳布孔形式，选择最优爆破孔网参数。试验结果表明：用平行束状孔取代扇形落矿，改善了爆破效果，简化了采场结构，减少了采切工程量。     

Electrochemical intercalation in NiOx thin films

In this work we investigated the mechanism of the electrochemical intercalation reactions in rf sputtered nickel oxide thin films electrodes by two techniques: mechanical stress change measurements by means of an optical technique and mass changes using an electrochemical quartz microbalance (EQCM). The experiments were performed in alkaline electrolytes containing cations of the first column of the periodic table. Reversible mass and volume changes were observed. In order to explain these experimental results, an exchange reaction is proposed, in which the oxidation process is accompanied by the deinteractional of a relative large number of “light” cations, simultaneously with the intercalation of a smaller number of heaviest cations.     

Longitudinal elastic waves in columns due to earthquake motion

An analysis is presented of longitudinal waves in a thin elastic column. Velocity is specified at one end, and the boundary condition at the other end is expressed in terms of a range of effective impedances of an attached structure. Propagation, reflection and interference of the waves are followed by the method of characteristics. Integration of differential equations along characteristics yields the wave-induced stress, which is then applied to problems of earthquake excitation. Numerical examples are given for recorded updown ground motion of the Kobe Earthquake.     

Surface stress effects on the thermodynamics of epitaxy

An analysis of the thermodynamics of epitaxy in thin films is presented which includes the effects of the surface stresses of the free surface and the film-substrate interface. It is shown that these effects, which are usually ignored in the theory of epitaxy, can have a major influence on both the critical thickness for epitaxy and on the partitioning of the misfit strain between the volume elastic strain and interface dislocations.     

圆杆弹性和弹—塑性扭转公式的探讨

对圆杆在线弹性阶段，弹－塑性阶段和全塑性阶段的扭转剪应力的计算公式作了分析，并推导了在材料的应力－应变关系（τ－γ关系）不服从虎克定律时，扭转真实剪应力的计算公式。文中对扭转强度计算公式的来源，物理含义及其都作了详细的说明。这对执行和理解国家ＧＢ１０１２８－８８《金属室温扭转试验方法》是有益的，而且对高校中材料力学的教学具有一定的参考价值。