5ZV25J-10160窄V胶带失效原因及改进措施

对川南矿区使用的5ZV25J－10160联组窄V胶带的损坏情况进行了观察分析，主要损坏原因有：胶带V形夹角与带轮轮槽夹角不一致，胶带顶部宽度与带轮轮槽开口宽度不符合要求，在传递动力中造成带轮顶部与胶带联结层接触而单根胶带悬空；胶带硫化质量差、配组不当；胶带及带轮安装、调校未达到要求。对此提出如下改进措施：规定胶带V形夹角和带轮轮槽夹角均为40°，单根胶带顶部宽25mm，带轮轮槽开口宽23．4mm；胶带必须严格按规定配组、安装、调校。实践证明，经改进后胶带传动平稳，无异常损坏。     

GaAs FET辐射退化研究

低噪声ＧａＡｓ ＦＥＴ和功率ＧａＡｓ ＦＥＴ经中子辐射都未发生致命性的通或断失效，直流偏置伏态下，其失效模式仅仅表现为源漏饱和电流ＩＤＳＳ的退化降低，据此提出了ＩＤＳＳ退化失效与快中子注量φｎ之间的解析关键式ｌｎｙ＝ａ＋ｂｌｎφ。     

Conductor design with high-Tc superconducting Bi(Pb)—2223/Ag multifilamentary tapes

With high upper critical fields, high temperature superconductors (HTSC) have been recognised as candidate materials for coil and magnet applications. High field devices, at one time or another, when operated close to their rated limits are often faced with instability problems which normally are electrical, magnetic or mechanical in nature. The determination of stability parameters, therefore, is of interest to the conductor designer which very much assists in the processing aspect of long length production of wires and tapes. Due to the morphology of the superconductor most HTSC devices made with Bi(Pb)—2223 precursor exist in tape form. Here the determination of stability parameters (for flux-jump and cryogenic stability) for multifilamentary Bi(Pb)—2223/Ag tapes are presented. Processing parameters such as intermediate deformation and filling factors have been found to play a crucial role, not only on the critical current density of the tapes but on the stability aspect in conductor design as well.     

氦－镉激光器的失效机制

本文报道国产氦－镉激光器常出现的导致失效的一些现象，并阐明其机制。同时给出一些改进意见及修理方法。     

Failure analysis and wear mechanism study of a heavily loaded gear

Failure analysis and a study of the wear mechanism were performed on a heavily loaded carburized gear with some unusual features. The analysis showed that the different failure forms on the tooth surface of the gear were dependent on the sub-surface shearing stress, the lubrication conditions and the surface roughness. Delaminations formed on the addendum surface were the main reason for the gear failure. A suggestion for improvement has been tried, and a desirable result has been obtained.     

堆底熔穿事故的场外后果及其对策

在压水堆核电站应急计划和应急响应中，堆底熔穿事故占有重要位置。本文用法国核电厂事故源项Ｓ３（对应于堆底熔穿事故）计算了在典型气象条件下的场外放射学的后果，根据一般防护决策原则和我国颁布的干预水平，提出了保护公众的应急防护措施的建议。     

PTN网络的二次断纤链路规划算法

在PTN（PacketTransportNetwork）网络规划建设中,需要对光纤链路留出备份带宽,以保证部分光纤断开时,受影响业务有足够的容量进行路由重组。这也是提高网络生存性的有效方法之一。文中首先遍历网络双链路的失效状态,然后断开网络中任意两条链路,通过逐次增加链路容量来保证失效业务能够重组路由;最后提出二次断纤链路容量规划算法并进行试验仿真。结果表明,该算法在节约网络带宽、降低建造成本以及故障容错方面有着良好性能,能够很好应用于传送网络的链路规划中。     

计算机网络故障检测

计算机网络故障种类较多,计算机网络故障检测是一个复杂的系统工程,不仅对网络故障处理步骤有所要求,而且对网络故障分析方法以及计算机故障维护都有极高的要求。为此,本文也主要从这几个方面对计算机网络故障检测进行分析。     

水工钢闸门主梁模糊失效概率计算方法研究

为合理计算水工钢闸门主梁模糊失效概率,分别将主梁相对变形当作一个随机变量及三个变量的组合,采用积分法、当量随机化方法及蒙特卡罗法进行了计算。当相对变形为一个随机量时,采用积分法及当量随机化方法计算,两者的差别在于积分法用隶属函数描述模糊限值,当量随机化方法是将模糊限值当量作为一个随机量。当相对变形看作三个变量的组合时采用蒙特卡罗法进行计算,该方法考虑了三个变量的分布特性,更符合实际情况,模糊限值也用随机量表示。计算表明,积分法与当量随机化方法结果相近,验证了当量随机化方法的精度;蒙特卡罗法结果与相对变形服从正态分布时、用当量随机化方法计算的结果接近,故主梁相对变形服从正态分布更为合理。三种计算方法中,当量随机化方法计算失效概率相较于其它方法有计算过程简便,效率高的优点。     

Observer‐based Reliable Control for Discrete Time Systems: An Average Dwell Time Approach

This paper deals with the problem of reliable control for discrete time systems with actuator failures. The actuator is assumed to fail occasionally and can recover over a time interval. During the time of suffering failures, the considered closed‐loop system is assumed unstable. Using an average dwell time method and under the condition that the activation time ratio between the system without actuator failures and the system with actuator failures is not less than a specified constant, an observer‐based feedback controller is developed in terms of linear matrix inequalities such that the resulting closed‐loop system is exponentially stable. An example is included to demonstrate the effectiveness of the proposed approach.