Electrodeposition, composition and structure of Zn—Cr alloys

The effect of polyethylene glycol (PEG 1500) as additive and of deposition conditions on Zn—Cr alloy electrodeposition from an acidic sulfate electrolyte at room temperature, without agitation was investigated. PEG polarizes the overall cathodic reaction and inhibits Zn deposition. Cr codeposition with Zn starts at a cathodic potential of about –1,95 V vs Hg/Hg₂SO₄, which is reached at current density of about 20 A dm^–2 in galvanostatic conditions. Zn—Cr alloy coatings containing up to 28 at % Cr were obtained depending on the plating conditions. SEM observations showed an island-like structure, formed by the local growth of crystals, which covered the surface during further deposition. In the first stages of electrodeposition the powder diffraction spectra contain lines of b.c.c. -(Zn,Cr) phase (a 3.02 Å). After 30 s deposition time weak lines of Zn-based phase (a 2.67 Å, c 4.90 Å) appear, and become clearly visible in coatings deposited for 90 s. The average Cr content in the alloy coatings decreases with advancing deposition. The as-plated surface contains C in organic compounds and Zn(OH)₂. After 50 min sputtering, Zn and a mixture of Cr, Cr₂O₃ and Cr₇C₃ were found. The presence of organic C and O, probably from inclusions of PEG, were also detected.     

Effects of electrolyte in dye-sensitized solar cells and evaluation by impedance spectroscopy

Effects of the electrolyte of DSCs on impedance spectra were evaluated by changing concentration of redox couple, viscosity, and additives to electrolyte. The relation with current-voltage characteristics (I-V characteristics) was investigated. In many cases, the impedance component attributed to charge transfer at TiO₂|electrolyte interface demonstrated strong relation with the I-V characteristics. The recombination of electrons in TiO₂ with I₃⁻ in electrolyte was a key factor in determining performance of DSCs. To evaluate the effect of I₃⁻, diffusion-limiting current in the electrolyte for various viscosities was evaluated by cyclic voltammetry. When the short circuit current (SCC) was almost equal to the diffusion-limiting current, strong influence of the diffusion coefficient on the impedance spectra was observed: impedance arcs were enlarged as the diffusion coefficient was decreased. On the other hand, when the diffusion-limiting current was larger than the SCC, photo-excitation and electron injection processes became dominating factors in the DSCs performance. The SCC was regulated by the charge recombination process at TiO₂|electrolyte interface, and thus the impedance component ω₃ was related to the performance in such condition.     

Electrochemical and spectroscopic evidences of corrosion inhibition of bronze by a triazole derivative

The electrochemical behavior of the bronze (Cu-8Sn in wt%) was investigated in 3% NaCl aqueous solution, in presence and in absence of a corrosion inhibitor, the 3-phenyl-1,2,4-triazole-5-thione (PTS). The inhibiting effect of the PTS was evidenced for concentrations higher than 1 mM for the cathodic process whereas its effect was clearly seen with a concentration as low as 0.1 mM for the anodic process. A significant positive shift of the corrosion potential was also observed, and its inhibiting effect increased with both its concentration and the immersion time of the sample. From voltammetry and electrochemical impedance spectroscopy experiments, the inhibiting efficiency of the PTS was found to be in the 94-99% range for 1 mM concentration. Scanning electron microscopy and X-ray energy dispersion analysis of the specimen surface show the presence of sulphur on the surface. Raman micro-spectrometry study confirms the protective effect of the PTS in aqueous solution through three types of interactions with the electrode, namely the adsorption of the inhibitor in a flat configuration, the formation of copper-thiol molecules, and when copper is released, the formation of a polymeric complex.     

Characterization of multiwall carbon nanotubes and influence of surfactant in the nanocomposite processing

Carbon nanotubes prepared by a classical CVD method with a nickel catalyst have been characterized, then used as conducting anisometric objects dispersed into a polymeric matrix. In a first part, these nanotubes are structurally characterized before and after heat treatments (HTT=1500, 2000, 2500 °C). Diffusion Raman experiments and diamagnetic susceptibility experiments demonstrated their limited graphitized structures.Then, in a second step, a well defined processing way to prepare nanocomposites with a standard epoxy resin is presented. In particular, the use or not of a non-ionic surfactant (Tergitol) to disperse these nanotubes is analyzed. The influence of nanotube contents is examined on the bulk nanocomposite density, the glass transition temperature of the nanocomposites, and the d.c. electrical conductivity behavior. These results demonstrated that the interfacial properties are playing a fundamental role. On one hand, the glass transition temperature is increasing with the nanotube content, and on the other hand, the percolation threshold is found for a rather high critical volumic concentration. Finally, it is demonstrated that a pure geometrical model is not sufficient to explain these behaviors and that a wrapping effect of the organic matrix around the nanotubes has to be considered.     

Strong influence of buffer layer type on carbon nanotube characteristics

Carbon nanotubes (CNTs) have been grown by chemical vapor deposition in a vacuum chamber equipped with in situ photoelectron spectroscopy technique that allows for precise characterization of the chemical state of substrate and catalyst before the CNTs growth. The CNTs were grown onto Si wafers covered with thin buffer layers of Al, Al₂O₃, TiN, and TiO₂, using Fe as catalyst. Marked differences were observed both in growth rate and nanotube characteristics, as determined by SEM, TEM and micro-Raman spectroscopy, depending on the choice of buffer layer.     

有机磷化物制备羟基磷灰石工艺条件的探讨

探索用有机磷化物制备羟基磷灰石的工艺条件：采用硝酸钙、氨水、磷酸三丁酯为原料进行正交对比研究，优化得到了制备较佳羟基磷灰石的工艺条件。优化的工艺条件为：原料中Ca／P（molar ratio）1．67；Ca（NO3）2、4H2O／NH3H2O（g／g）为0.99；烧结温度为850℃：恒温时间为5h，并对合成的样品进行了化学和红外光谱的分析。     

(Ag)_核·(Au)_壳复合纳米粒子的制备

以银原子团簇作晶种,采用微波高压液相合成法制备了分散性好、规则球形的(Ag)核·(Au)壳复合纳米粒子。研究了(Ag)核·(Au)壳复合纳米粒子的紫外可见吸收光谱和共振散射光谱特性。结果表明,液相(Ag)核·(Au)壳复合纳米粒子和高压微波合成的液相金纳米粒子的最强共振散射峰均在580nm处,它们的吸收光谱图相似,最大吸收分别在518.5nm和524.8nm。     

Infrared study of salt free and salt treated cellulose pyrolysis under nitrogen atmosphere

The pyrolysis under nitrogen of salt free and salt treated cellulose was studied by infrared spectroscopy. The results confirm the unzipping mechanism suggested by DTA and TGA studies, and show this mechanism to apply to the untreated and salt treated samples. The results also show the unzipping to stop at the stage of char formation. The onset of this stage was found to occur after the volatilization of only 45–50% of the initial sample of the borax treated cellulose, compared with 65–70% of the KCl treated cellulose and 80–85% of the untreated cellulose.     

Surface and Interfacial Studies of Plasma-Modified Composite Surfaces

Model epoxy and bismaleimide compounds in thin film form were used to simulate epoxy and bismaleimide composite surfaces, in order to study compositional changes and interfacial reactions induced by oxygen plasma treatment. X-ray photoelectron spectroscopy (XPS) and infrared reflection-absorption spectroscopy (IR-RAS) were used to probe chemical changes which occurred. XPS and IR-RAS were found to be complementary techniques in determining the nature of functional groups incorporated into surfaces by plasma treatment. IR-RAS analysis of the model surfaces following exposure to a liquid epoxy resin revealed that while adsorption of the liquid epoxy occurred on both plasma-treated and nonplasma-treated surfaces, the oxygen plasma-treated surface alone was capable of initiating ring-opening reactions in the epoxy. However, this effect was not observed unless immediate contact was made between the plasma-treated surface and the liquid epoxy resin, illustrating the short-lived reactivity of the functional groups on the plasma-treated surface.     

Softening and melting mechanisms of polyamides interfering with sliding stability under adhesive conditions

The thermal stability of polymers is a main issue when used as friction elements under dry sliding. Cast polyamide grades processed with either natrium or magnesium catalysors are slid on a small-scale and a large-scale test configuration to reveal the effect of softening or degradation on the sliding stability and to investigate possibilities for extrapolation of friction and wear rates between both testing scales. The combination of softening and afterwards transition into the glassy state is detrimental for the sliding stability of natrium catalysed polyamides, characterised by heavy noise during sliding. A transfer film formed under continuous softening also provides high friction. Melting during initial sliding is necessary for stabilisation in both friction and wear, and eventual softening of a molten film near the end of the test then not deteriorates the sliding stability. Softening of magnesium catalysed polyamides is favourable for the formation of a coherent transfer film resulting in more stable sliding than natrium catalysed polyamides. The differences in softening mechanisms of both polyamide grades is correlated to structural changes investigated by thermal analysis and Raman spectroscopy: the γ crystalline structure prevails in magnesium catalysed samples and the α crystalline structure is predominant in natrium catalysed samples. For internal oil lubricated polyamides, a time dependent degradation of the polyamide bulk deteriorates the supply of internal oil lubricant to the sliding interface, resulting in high friction and wear under overload conditions. As the degradation mechanisms during sliding are strongly correlated to the test set-up, extrapolation is only possible for friction in a limited application range, while wear rates cannot be extrapolated.