沙袋充填度与稳定性的试验研究

沙袋筑坝在工程中愈来愈广泛的应用，需要解决的问题也很多，笔者对不同尺寸沙袋的充填度进行了讨论，提出了极限充填度和最佳充填度的概念；通过对不同尺寸充沙沙袋在水泥抹面和沙袋布为底面的水槽中所得的试验资料的分析，得出了充沙沙袋的失稳流速。     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

基于SHARC数字脉压系统的设计与实现

详细介绍了采用两片浮点DSP ADSP21062实现某舰载雷达所需要完成的舰速补偿、反异步干扰和脉冲压缩的系统研制。通过采用分段匹配滤波的方法，极大地节约了时间和空间。与完成同样功能采用单片TMS320C6701的设计相比，本设计具有外围电路简单、系统调试容易等优点。     

Deep‐UV Photochemistry and Patterning of (Aminoethylaminomethyl)phenethylsiloxane Self‐Assembled Monolayers

The 193 nm photochemistry of (aminoethylaminomethyl)phenethylsiloxane (PEDA) self‐assembled monolayers (SAMs) under ambient conditions is described. The primary photodegradation pathways at low exposure doses (< 100 mJ cm^–2) are benzylic C–N bond cleavage (ca. 68 %), with oxidation of the benzyl C to the aldehyde, and Si–C bond cleavage (ca. 32 %). Amine‐containing photoproducts released from the SAM during exposure remain physisorbed on the surface, where they undergo secondary photolysis leading to their complete degradation and removal after ca. 1200 mJ cm^–2. NaCl(aq) post‐exposure rinsing removes the physisorbed materials, showing that degradation of the original PEDA species (leaving Si–OH) is substantially complete after ca. 450 mJ cm^–2. Consequently, patterned, rinsed PEDA SAMs function as efficient templates for fabrication of high‐resolution, negative‐tone, electroless metal and DNA features with good selectivity at low dose (i.e., ca. 400 mJ cm^–2) via materials grafting to the intact amines remaining in the unirradiated PEDA SAM regions.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

考虑弯道环流影响的平面二维水流泥沙数学模型

弯道环流是影响断面流速和含沙量分布的重要因素。本文提出了通过求解立面二维弯道环流运动的方法,在平面二维水流泥沙数学模型中考虑弯道环流的作用。该方法适用范围广,增加计算工作量不太大。     

The process window for diamond deposition from the vapor phase with sulfur in the C–H–O feed gas mixtures

Theoretical predictions using a modified radical species ternary diagram for C–H–O system indicate that addition of sulfur expands the C–H–O gas phase compositional window for diamond deposition. Sulfur addition to no-growth domain increases the carbon super-saturation by binding the oxygen and the addition of sulfur to the non-diamond domain reduces the heavy carbon super-saturation by decreasing C_nH_m species concentration in the gas phase. The overall effect of sulfur addition to gas phase mixtures is characterized as that of oxygen addition to the C–H system, i.e. expansion of the compositional window over which diamond can be deposited from the gas phase. In addition, the increasing sulfur concentration to diamond domain feed gases beyond 2000 ppm did not affect the steady state gas phase composition but the quality of diamond was reduced.     

A simple correlation for gas bubbles rising in power‐law fluids

Recently, the author (Rodrigue, 2001 a, b) proposed a generalized correlation for the steady rise of gas bubbles in uncontaminated viscous Newtonian fluids of infinite extent. It is the purpose of this note to show that this model can be modified for inelastic non‐Newtonian power‐law fluids. Using data taken from six different studies, it is shown that the modified model can predict quite nicely the bubble velocity for these non‐Newtonian inelastic fluids.