单模光纤的传输衰减随温度变化的研究

本文从实验上测量了单模石英光纤在－50～120℃范围内的损耗。随着温度升高，光纤的损耗随之降低，在常温附近达到最小。其后损耗随着温度的继续升高而增加。损耗的变化主要是由于杂质的吸收和微弯损耗。本文对杂质的吸收以及微弯损耗进行了数值模拟，并且从理论上定性地解释了损耗对温度的依赖关系。     

Absorption of materials by or through the living skin

The skin comes into contact with a large range of materials either deliberately or inadvertently. It should be possible to predict the exact transport rates of these materials through the skin as a function of the physicochemical properties of the different compounds. With this sort of knowledge it is possible to predict the exact disposition of compounds and use this in the formulation of new products both in the pharmaceutical and cosmetic field. The information will also be useful from the standpoint of skin toxicology and environmental health. In order to be able to predict this complex process it is necessary to split the overall transport into different component parts. This article will identify these components and provide illustrations. The major areas discussed will be barrier function of the skin, the release properties of different topical formulations and how these may be monitored. Novel means of enhancing the penetration of drugs will be discussed and how some additives that are incorporated into formulations will perhaps alter the barrier function of skin. A mathematical model describing skin penetration has been developed and its use in predicting blood levels will be described. This model has been tested both in animal experiments and in limited human studies and its relevance to these situations will be highlighted.
Absorption cutanée et transcutanée in vivo     

Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.     

高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。     

用稳态反饱和吸收法测量C_（60）的激发态吸收截面

用准连续激光实现了Ｃ６０的稳态反饱和吸收，通过实验和理论计算的拟合，确定了Ｃ６０的三重第一激发态吸收截面。     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

Energy absorption in splitting square metal tubes

This paper presents an investigation into the energy absorbing behaviour of axially splitting square metal tubes. Tubes 50 mm square with a variable thickness were pushed slowly against rigid pyramid shaped dies, which had various semi-angles. By pre-cutting 5 mm long slits at the four corners, the tube splits along the corners and curls outward with a certain radius at a constant force. In this energy dissipating system, there are three components: tearing energy, plastic deformation energy and frictional energy. Theoretical analysis of the three energy components is presented. Curl radius is also studied in detail. Good agreement between experiments and theory is obtained. The results show that tubes which both split and curl may be used as efficient, long stroke energy absorbing devices.     

用AIR-C2H2原子吸收光谱法测定镉镍电池正极浸渍液中钴含量

本文主要简述与运用AIR-C2H2原子吸收光谱法进行镉镍电池正极浸渍液中钴含量的测定，介绍了钴最佳测定条件及呈良好线性范围的浓度。同时对样品消化处理条件，在测定中样品的干扰因素进行了综合考虑，该方法具有很好的灵敏度，很好的重复性，干扰小，同时具有方法步骤简单，操作容易掌握等特点，对样品钴含量的测定，其相对标准偏差均小于1.0%（n=6），标准加入回收率均在97.0%～102.0%(n=5）范围内，结果表明，运用AIR-C2H2原子吸收光谱法测定镉镍电池正极浸渍液中钴含量的分析，达到了实验室分析质量控制的要求，完全适用于镉镍电池正极浸渍液中钴含量的控制分析和样品系统分析。     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

钛及钛合金中氧和氢的联合测定

叙述了用红外吸收法对钛及钛合金中氧和氢联合测定的方法，取得了测定的最佳条件。连续测定6次的相对标准偏差在10％以下，作加标回收试验的回收率为95．6％～103．9％。分析时间在3min以内，可应用于日常分析，结果满意。