Strength, durability and micro-structural aspects of high performance volcanic ash concrete

This paper presents the results of investigations to assess the suitability of using volcanic ash (VA) as a cement replacement material to produce high performance concrete. Tests were conducted on concrete mixtures replacing 0 to 20% by mass of ordinary Portland cement (OPC) by VA. The performance of high performance volcanic ash concrete (HPVAC) mixtures was evaluated by conducting comprehensive series of tests on fresh and hardened properties as well as durability. The mechanical properties were assessed by compressive strength, while durability characteristics were investigated by rapid chloride permeability (RCP), drying shrinkage (DS), mercury intrusion porosimetry (MIP), differential scanning calorimetry (DSC) and microhardness tests. HPVACs showed better durability properties compared to control concrete with 0% VA. The improved performance of HPVACs was attributed to the refinement of pore structure, and pozzolanic action of VA. HPVAC having a minimum 28-day compressive strength of 60 MPa can be obtained by replacing up to 20% (by mass) of cement by VA. Development of non-expensive and environmentally friendly HPVAC with acceptable strength and durability characteristics (as illustrated in this study) is extremely helpful for the sustainable development and rehabilitation of volcanic disaster areas around the world.     

偶联剂对地砖用PVC填充材料相态结构和力学性能的影响

研究了钛酸酯类偶联剂和硅烷类偶联剂对钙矿、硅酸盐填充的PVC填允材料力学性能、相态结构、密度、热失重率及吸水伸长率和耐热阻燃性能的影响。结果表明,偶联剂可改善填充PVC的抗冲性能,降低其拉伸强度,扫描电镜分析表明,填料越细,分散越均匀,越易被PVC树脂所包覆,力学性能越好,研究得到了比重大、热失重率低、吸水伸长率小、阻燃耐烧灼性好的高填充PVC硬质塑料地板砖。     

氯化铁催化乳酸的酯化作用

报道了氯化铁水合物催化乳酸和醇的酯化作用制备了１５种乳酯。     

5-氯甲酰氧基异肽酰氯的制备

以三光气(简称BTC)为酰氯化剂,与 5 -羟基异酞酸在复合催化剂作用下制备了 5- 氯甲酰氧基异肽酰氯(简称CFIC),收率最高可达 42 .3%。分析了反应条件的改变对产品收率的影响。反应物量比R〔n(三光气)∶n(5- 羟基异酞酸)〕≤1 .1时,产品收率很低,几乎得不到产品; 1. 11 7时,影响不大。溶剂极性越大,反应越快,收率越高。复合催化剂(三乙胺 /咪唑、吡啶 /咪唑)的催化效果远远优于单一催化剂(N,N -二甲基甲酰胺、三乙胺、吡啶和咪唑)。反应适宜在 5 ~20℃操作,温度高于 30℃时,反应很难进行。反应时间较短时,对产品收率影响较大,当时间大于 24h后,影响不大。利用正交实验确定的最佳工艺条件为:反应物量比为 1. 67;催化剂为m(咪唑)∶m(吡啶) =1∶4及m(吡啶+咪唑)∶m(三光气) =0. 08∶1;反应温度5~10℃。用红外光谱仪分析产品的主要官能团:在 1785. 24、1764 .12、1603 .20cm-1和 1557. 99cm-1处有强吸收峰,它们分别为Ar—OCOCl、Ar—COCl与三取代基苯环。用高效液相色谱仪测得w(CFIC) =99. 4%,用数字熔点仪测得产品熔点为 56. 7~57. 0℃。推测了三光气在催化剂作用下的反应机理。     

阳离子香豆胶的合成及结构表征

以3-氯-2-羟丙基三甲基氯化铵(HAT)为阳离子醚化剂,天然香豆胶为原料,异丙醇为分散剂制得季铵盐型阳离子香豆胶。研究了HAT、催化剂NaOH、反应温度和反应时间对合成阳离子香豆胶(CFG)的影响,用凯氏定氮法测定了CFG的取代度。合成CFG的优化实验条件为:m(香豆胶)∶m(异丙醇)∶m(HAT)∶m(NaOH)=1∶(1.6~2)∶(0.15~0.3)(∶4~8),反应温度40~50℃,反应时间2~3 h,制得的产品能满足工业应用要求的黏度及取代度范围(500~800 mPa.s,DS=0.86~1.32)。用FTIR和13CNMR对CFG的结构进行了表征。     

Water sorption of poly(vinyl alcohol)/ poly(diallyldimethylammonium chloride) interpenetrating polymer network hydrogels

Temperature‐responsive interpenetrating polymer network (IPN) hydrogels constructed with poly(vinyl alcohol) and poly(diallyldimethylammonium chloride) using the sequential IPN method were studied. The characteristics of IPN hydrogels were investigated using the dynamic vapor sorption system. IPN hydrogels exhibited a relatively high sorption ratio, 180–360% at room temperature. The sorption ratio of hydrogels depended on temperature. Diffusion coefficients were calculated according to the Fickian Law at several temperatures. The apparent activation energy was 5.43 kJ mol^?1, which corresponds to typical diffusion processes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1389–1392, 2003     

固相法氯化聚乙烯与聚氯乙烯共混物的形态与性能

研究了聚氯乙烯(PVC)与固相法氯化聚乙烯(CPE)共混物的应力-应变行为和冲击强度对CPE用量和氯含量的依赖关系,考察了共混物形态与性能的关系。动态力学性能和透射电子显微镜的研究结果表明,PVC/CPE为部分相容体系,两相间存在着一定的相互作用,当CPE氯含量为36％～42％,用量为7～15份时,CPE在PVC/CPE共混物中形成比较完整的网络结构、共混物具有更好的抗冲击性能。Brabender流变仪研究表明,CPE能促进PVC的塑化,共混物的加工性优于纯PVC。     

3-氯-2-羟丙基三甲基氯化铵的制备

通过系统的实验研究,探索出3 氯 2 羟丙基三甲基氯化铵(CHPTMAC)的最佳生产工艺条件:n(环氧氯丙烷)∶n(三甲胺盐酸盐)=0 95∶1,反应起始pH=7 5～8 0,反应温度采用分段控制(10℃,35℃),使用合适的催化剂,反应收率可达96%以上。通过连续水汽精馏对产品进行纯化,纯化后的产品中w(CHPTMAC)=69%,w(环氧氯丙烷)≤0 0005%,w(二氯丙醇)≤0 0015%,产品性能良好,已投入生产。     

PP/PVC/PP-g-(St-co-MMA)的形态结构

以苯乙烯一甲基丙烯酸甲酯共聚物接枝聚丙烯[PP—g-（St—co—MMA）]为相容剂，利用扫描电子显微镜（SEM）和x射线能谱仪（EDS）对PP／PVC／PP—g-（St—co-MMA）的形态结构进行了研究。由x射线能谱微区分析得到了共混物中氯元素面分布图，对氯元素面分布进行了粒径统计。结果表明，在PP／PVC中加入PP-g-（St—co—MMA）相容剂，共混物亚微观相形态结构发生了变化。PP—g-（St—co—MMA）能够明显降低PP／PVC共混物中PVC分散相的分散尺寸，提高共混物两相之间的相容性。改变相容剂的用量和共混物的组成，都对体系的形态结构产生影响。     

PVC型材低温落锤破裂影响因素的分析

从型材内筋壁厚、加工助剂、辅助原料、塑化控制、模具流道等方面分析了PVC型材低温落锤破裂影响因素，并提出了提高PVC型材低温落锤冲击性能的建议。