Preparation and catalytic performance of Co3O4 catalysts for low-temperature CO oxidation

Without use of any surfactant or oxidant, a series of Co₃O₄ catalysts have been prepared from cobalt nitrate aqueous solution via a very simple liquid-precipitation method with ammonium acid carbonate followed by calcination at various temperatures. The catalytic performance of the Co₃O₄ for CO oxidation has been studied with a continuous flowing laboratory microreactor system. The results show that the CO conversion of all the samples can reach 100% at ambient temperature. The catalyst calcined at 300 °C is able to maintain its activity for CO complete oxidation more than 500 min at 25 °C and about 240 min even at −78 °C. High reaction temperature results in a high catalytic stability, while the catalytic stability decreases with further increasing the reaction temperature. Characterizations with X-ray powder diffraction and transmission electron microscopy suggest that all the samples exist as a pure Co₃O₄ phase with the spinel structure, the samples are apt to aggregate and the specific surface area gradually decreases with increasing the calcination temperature, which directly leads to the decrease of catalytic stability. Furthermore, the amount of active oxygen species measured by CO titration experiments appears to be critical for catalytic performance.     

基于活动区域的移动无线传感器网络路由协议

为了解决移动无线传感器网络中能量效率问题,提出了一种基于活动区域的移动无线传感器网络（WSN）路由协议。本方法使用源和sink节点相对位置来形成路由的活动区域,网络中的移动节点使用睡眠唤醒模式来节约能源。移动向量信息（如当前位置、方向和速度）以及节点的剩余能量,用于选择能够提供最大连接保留时间的邻居,移动向量信息也被用来唤醒活动区域中的移动节点。实验表明,与其他路由协议进行比较,该方法在分组传输过程中具有更高的可靠性。     

天然茶皂素的提取及泡沫性能

茶皂素是一种天然的表面活性剂 ,通过几种浸取剂的研究 ,表明 60 %甲醇溶液为最好浸取剂。浸取温度 40℃～ 50℃ ,浸取时间 4 5h左右。浸取的茶皂素与多种表面活性剂比较 ,说明它是一种发泡性好、泡沫稳定性优良的发泡剂     

瀑-深梯级AGC厂间负荷实时分配策略研究及应用

为了实现瀑布沟、深溪沟电站的实时联合运行控制,基于分层调管的原理,以深溪沟电站水位控制为目标,提出了一套能够实现瀑布沟和深溪沟两站水量与电量平衡的厂间负荷实时分配策略及求解流程。针对厂间负荷分配时,不同机组组合下的虚拟单台机组的发电特性曲线和振动区,分别采用动态规划技术和集合区间运算法给予求解,同时还给出了一种简单实用的厂间联合躲避振动区的策略。在此基础上,开发的集控侧梯级AGC系统,已成功地应用到了大渡河瀑布沟和深溪沟梯级实时联合运行控制中,且计算结果满足实际运行工况的要求。     

Active sites in methanol oxidation on Cu(110) determined by STM and molecular beam measurements

STM has been combined with molecular beam rate measurements to gain an understanding of the oxidative dehydrogenation of methanol to produce formaldehyde, both at the macroscopic and microscopic level. From this a model of the reaction is developed where the methanol initial reacts at very few active oxygen sites located at the short sides of oxygen islands on the Cu(110) surface. Such sites are very much rarer on a surface which is saturated with 0.5 monolayers of oxygen and the reaction rate is initially very low, but shows autocatalytic behaviour, rising in time as vacancies are created in the oxygen layer.     

The mechanism of the poisoning of ammonia synthesis catalysts by oxygenates O2, CO and H2O: an in situ method for active surface determination

The effect of adding an oxygenated poison (O₂, CO or H₂O) to a hydrogen/nitrogen stream producing ammonia over a triply promoted (K₂O, CaO, Al₂O₃) commercial catalyst is not unsurprisingly rapidly to poison the catalyst. However, immediately the oxygenated poison reacts with the catalyst and before total poisoning has occurred, which in these experiments took 10 min, there was an explosive release of ammonia producing concentrations in the gas phase in excess of the equilibrium value. This is thought to be due to a convulsive reorganisation of the surface of the catalyst in forming regions of an oxide overlayer, resulting in the expulsion of the standing surface nitrogen atom coverage as ammonia. However, in contradistinction to the observation of complete poisoning of the triply promoted catalyst shortly after switching the water (2.9%) into the hydrogen/nitrogen stream, when polycrystalline iron was used as the catalyst, after the initial pulse of ammonia was observed, the small quantity of water (2.9%) in the hydrogen/nitrogen stream resulted in an increased rate ( ×3) of ammonia synthesis which declined only slightly over the twenty minute duration of the experiment. The difference in behaviour between the triply promoted catalyst and the polycrystalline iron is thought to be due to the relative ease of reduction of the latter, so that submonolayer quantities of oxide can be stabilised on the surface of the polycrystalline iron. The promoting effect of this oxide overlayer is either structural or electronic; no distinction can be made from these experiments. The technique of injecting either O₂ or CO into a hydrogen/nitrogen stream which is producing ammonia over promoted catalysts in quantities insufficient to cause complete poisoning and measuring the oxygen coverage of the catalyst to a measured decrease in the ammonia synthesis rate, appears to be a ready, in situ method for the determination of the active catalyst area.     

Nano-sized carbon hollow spheres for abatement of ethylene

In this paper, the ethylene adsorption capacities of the nano-sized carbon hollow spheres (CNB) and active carbon (AC), the Pd (PdCl₂) impregnated CNB or AC (Pd/CNB, Pd/AC) and heat treatment under various conditions, were studied at different ethylene concentrations from 64 to 1060 ppm. The results indicated that AC had a good ethylene adsorption capacity at high ethylene concentration. Pd impregnation decreased the ethylene adsorption capacity of AC. Heat treatment and H₂ activation could increase the ethylene adsorption capacity, but also lowered than AC itself. CNB had lower ethylene adsorption capacity than AC, but heat treatment and H₂ activation could increase its ethylene adsorption capacity markedly. With activating condition from heat treatment in N₂ at 300 °C to activation in H₂/N₂ at 100 °C, to activation in H₂ at 200 °C, and to activation in H₂ at 300 °C, the ethylene adsorption capacity of Pd/CNB was increased regularly. At low ethylene concentration, viz., 64 ppm, the ethylene adsorption quantities (q _a) by Pd/CNB activated in H₂ at 200 or 300 °C were higher than any other adsorbents. So, activated in H₂ atmosphere at higher than 100 °C, Pd/CNB is particularly advantaged for adsorbing low concentration of ethylene. Amongst all the adsorbents used, Pd/CNB activated in H₂ atmosphere at 300 °C for 2 h has the highest ethylene adsorption capacity at lower concentration than 125 ppm. In addition, all the CNB, Pd/CNB, AC, and Pd/AC samples can be easily regenerated in airflow for more than 3 h.     

国内外活性氧化锌的进展

叙述了活性氧化锌的简史，特点、应用、生产方法的进展，活性的测定方法及标准。     

原煤流化床法制脱酚活性炭

以煤为原料，采用流化床一步法制取活性炭，考查了煤种、操作条件和矿物质对煤制活性炭脱酚性能的影响。同时综述了这方面的新成果，以期对该法制活性炭的脱酚性能得到全面了解。     

Understanding heterogeneous catalysis on an atomic scale: a combined surface science and reactivity investigation for the dehydrogenation of ethylbenzene over iron oxide catalysts

In order to study the dehydrogenation of ethylbenzene to styrene, epitaxial iron oxide model catalyst films with Fe₃O₄(111), -Fe₂O₃(0001) and KFe _x O _y (111) stoichiometry were prepared in single crystal quality on Pt(111). They were investigated using surface science techniques before and after atmospheric pressure reaction experiments in a newly designed single crystal flow reactor. As expected from low-pressure measurements, Fe₃O₄(111) is catalytically inactive. The catalytic activity of -Fe₂O₃(0001) starts after an activation period of about 45 min. After that, the surface is essentially clean but shows a high concentration of defects. On the potassium-promoted films, however, the activation period is much longer, the activity then is higher and the surface gets covered completely with carbon and oxygen during reaction. This indicates a different reaction pathway on the promoted films with a carbon–oxygen species as catalytically active species.