Dynamical adaptive synchronization

The notions of dynamical synchronization and adaptive dynamical synchronization problems are introduced. The algorithm solving adaptive synchronization problem for a subclass of Lurie systems with exciting input is proposed. The performance and potentialities of proposed solutions are demonstrated by two examples related to formation control and self‐organization of swarm systems. Copyright © 2006 John Wiley & Sons, Ltd.     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

Effects of mastication on the distribution of molecular weights and on the mechanical properties of native and commercial dental gutta percha (trans-polyisoprene)

Mastication of gutta percha (trans-polyisoprene) resulted in the selective scission of molecules, producing a narrower distribution of lower molecular weights. The mechanical properties of the samples also underwent a significant change due to mastication. The greater the content of incompatible substances (salts and oxides) in commercial gutta percha. the more substantial were these effects. The atmosphere (air, N₂, O₂) in which the experiments were conducted yielded significantly different results. The decrease in molecular weight was far greater in an O₂ atmosphere than under a current of nitrogen or air, owing to the combination of double bonds with O₂.     

Bioprocess applications of model-based estimation techniques

The last decade has seen the development of a number of approaches for estimating those variables which are difficult to measure on-line in industrial process situations. Whilst a range of techniques is available, a common element is the use of process knowledge in the form of a system model. In the case of bioprocess systems, although a large range of models has been presented in the literature, their use in estimation schemes on an industrial scale has been limited. A number of reasons can be identified for their low level of utilisation. Of particular significance is the uncertainty which exists in quantifying system performance and the process-model mismatch which inevitably results. The level of ‘pre-defined model’ uncertainty, together with the knowledge gained during the course of the fermentation, serves to dictate estimator structure. The paper considers a range of estimation strategies and contrasts, through industrial applications, their performance characteristics and utility.     

27keV Ar~+斜入射时的Cu-Au合金溅射实验角分布

用27keV Ar~+分别在垂直和倾斜入射情况下,轰击了Cu-Au(30wt％)合金样品,测量了Cu和Au原子的溅射角分布。角分布是用卢瑟福背散射(RBS)技术分析Al捕获膜上的Cu-Au沉积成分而定量得到的。结果表明:(1)在Ar~+倾斜(θ=40°)入射时,Cu原子择优发射,且程度比垂直入射(θ_r=O°)时增强:(2)倾斜入射时,Cu原子的角分布显示出在接近于样品表面法线方向的发射角范围内(θ<45°),发射机率比垂直入射时减小。     

厦门市气源转换的技术分析

分析了气源转换时原有输配系统的管道、调压设备、计量设备、用气设备与天然气系统相适应的问题，提出了相应的措施。     

Adaptive control in a heating vessel: A comparative study

This paper presents experimental results obtained in temperature adaptive control of a heating vessel. A non-linear model of the process showed that the feed flow rate causes severe variations in time constant and process gain. An extended horizon self-tuning controller and two different model reference adaptive controllers were tested. The influence of design parameters on control performance for each algorithm was assessed. The control system was disturbed with load and setpoint changes.     

Personal Exposure in Displacement Ventilated Rooms

Personal exposure in a displacement ventilated room is examined. The stratified flow and the considerable concentration gradients necessitate an improvement of the widely used fully mixing compartmental approach. The exposure of a seated and a standing person in proportion to the stratification height is examined by means of full-scale measurements. A breathing thermal manikin is used to simulate a person. It is found that the flow in the boundary layer around a person is able to a great extent to entrain and transport air from below the breathing zone. In the case of non-passive, heated contaminant sources, this entrainment improves the indoor air quality. Measurements of exposure due to a passive contaminant source show a significant dependence on the flow field as well as on the contaminant source location. Poor system performance is found in the case of a passive contaminant released in the lower part of the room close to the occupant. A personal exposure model for displacement ventilated rooms is proposed. The model takes the influence of gradients and the human thermal boundary layer into account. Two new quantities describing the interaction between a person and the ventilation are defined.     

Mechanics of sintering materials with bimodal pore distribution. III. Kinetics of sintering combined with various forms of loading and adhesion conditions

A study has been made on the effects of loading scheme and conditions restricting macroscopic strain on the work-hardening kinetics and strain accumulation in the solid state in sintering materials with bimodal pore size distributions. Active loading intensifies the reduction in the small pores. The greatest effect comes from combining sintering with hydrostatic compression. At the same time, kinematic constraints (partial or complete adhesion in surfaces) substantially retards the shrinkage of large pores, which means that the porous structure can be controlled. __________ Translated from Poroshkovaya Metallurgiya, Nos. 5–6(449), pp. 10–15, May–June, 2006.