Stretchable Gold Tracks on Flat Polydimethylsiloxane (PDMS) Rubber Substrate

A process to fabricate stretchable gold tracks on silicone rubber substrates is studied by XPS, static water contact angle measurement, AFM, and SEM. The process involves several steps: removing uncured oligomers by hexane Soxhlet extraction; pre-stretching the substrate; activating the strained silicone surface by an oxygen plasma treatment; coating the strained substrate with 5 nm titanium and 80 nm gold layers; and finally releasing the sample. The plasma treatment creates a thin brittle silica-like layer that temporarily increases the substrate's surface energy. Indeed, the plasma treatment is followed by a hydrophobic recovery. As a consequence, the delay between plasma treatment and metal deposition has to be reduced as much as possible. The silica-like layer can be nicely observed after release. The entire process allows us to obtain stretchable metallized samples that remain conductive even after an excessive deformation leading to electrical failure.     

Effect of carbon surface oxidation on platinum supported carbon particles on the performance of gas diffusion electrodes for the oxygen reduction reaction

The effect of carbon surface oxidation on platinum supported carbon particles (Pt/C) with nitric acid was investigated by cyclic voltammetry, electrochemical impedance spectroscopy, polarization experiments and chronoamperometry. Cyclic voltammograms, polarization curves and electrochemical impedance spectra showed that the treated catalyst had much larger active surface area and higher ionic conductivity than the untreated catalyst, and provided enhanced performance for oxygen reduction. The formation of acidic groups was examined by IR spectra. The Pt/C surface oxidation had a large effect on the performance of a gas diffusion electrode for oxygen reduction reaction.     

Water and salt permeability of reinforcement polymer‐gel composite membrane

The charged mosaic polymer membrane (CMM) without reinforcement and the composite charged mosaic polymer membrane (CCMM) with reinforcement were investigated in terms of salt and water transport (permeability). The composite charged mosaic polymer membrane (CCMM) with reinforcement showed a unique transport behavior such as preferential material transport L_p and ω. Water permeability coefficient, L_p and salt permeability coefficient, ω were estimated by taking account of active layer thickness of composite polymer gel. The L_p and ω values of CCMM with reinforcement were larger than those of CMM without reinforcement. On the other hand, the reflection coefficient of CCMM, σ, showed negative value, which suggested preferential material transport to solvent transport. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

空气压缩机无油润滑在山脚树矿的应用

山脚树矿有5台1966年上海生产的4L—20/8空气压缩机,运行很不经济,利用聚四氟乙烯合成材料制成活塞环,全部实现无油润滑运转,取得了良好的经济效益。     

"摩圣"技术在空气压缩机上的应用

介绍了4L-20/8型空气压缩机采用"摩圣"技术后的运行情况。"摩圣"技术在设备正常运行条件下能成功修复摩擦副的磨损,使之恢复原设计的尺寸和要求,因而提高了生产效率,取得了显著的经济效益。     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

Kinetics of phenol oxidation in a trickle bed reactor over active carbon catalyst

The wet air oxidation of phenol over a commercial active carbon catalyst was studied in a trickle bed reactor (TBR) in the temperature and oxygen partial pressure ranges of 120–160 °C and 0.1–0.2 MPa, respectively. The performance of the active carbon was compared in terms of phenol and COD destruction. The weight change of active carbon due to reaction was also measured. Finally, oxic phenol adsorption isotherms were assessed in batch conditions at 25, 125 and 160 °C. In order to use the conversion data obtained from the TBR for a kinetic study, special care was taken to check the kinetic control in the TBR experiments. Several kinetic models including power law or Langmuir–Hinshelwood expressions were considered to describe the catalytic oxidation of phenol over active carbon. The simple power law model with first order dependence on both phenol and oxygen concentration predicted satisfactorily the experimental data not only over the entire range of operating conditions studied, but also outside its validity range. Copyright © 2005 Society of Chemical Industry     

The Danish Twin Apartment Study – Part II: Mathematical modeling of the relative strength of sources of indoor air pollution

Abstract This study deals with the modeling of air pollution in apartments from laboratory measurements of source strengths, using formaldehyde and Total Volatile Organic Compounds (TVOCs) as model pollutants. The sources in two test apartments were grouped into two: building-related sources and occupant-related sources. The measured source strengths and ventilation rates were used for the prediction of concentrations expected in the apartments. These predictions were compared to measurements in the apartment over 12 months. The conclusions were that the model predictions based on emission rates measured in the laboratory can be used to predict the long-term concentration of the two model pollutants in the apartments. Considering the measured differences in ventilation between the apartments, an occupant emission rate of between 0.2 and 0.3 mg/h/kg body weight could be estimated. Based on previous suggested limits of acceptable exposures of humans to VOCs, an acceptable average emission rate of VOCs from building materials in general was estimated to be about 30 (μ/m²/h. The modeling showed that during the first 200 days, building materials dominated the emissions. After this, sources relating to the occupants dominated. On average about half of the VOC pollution originated from the building materials.     

A Study of Surface Deformation during Wire‐Rod Rolling of High Speed Steels using Experimental and Computational Techniques

The evolution of surface defects during shape rolling of high‐speed steel billets is studied using longitudinal surface defects prepared by machining and welding. The reduction of the defects during rolling in a production mill is compared to the total area reduction of the billets. Samples are collected after pass 4, 6, 8, 14, 19 and the final pass, 28, representing the finished 5.5mm wire. By inspecting the cross sections, the rotation of the billets from pass to pass is evaluated. Results from FE simulations on solid billets are compared to the experimental results. Generally, simulations predict less reduction than observed experimentally. In most cases cracks reduce most effectively followed by carbon steel welds and stainless steel welds.     

金属矿山深热矿井空气温度的灰色预测

金属矿山深热矿井气温的预测计算是一个难题，本文探讨了应用灰色系统预测理论来解决这一难题的新途径，并通过实例验证了该方法的可行性和有效性。