丙烯抗冲共聚产品EPF30R的开发

介绍了聚丙烯抗冲共聚产品EPF30R的工艺生产特点,并详细阐述了EPF30R重要物理性能与相关工艺控制参数的关系。通过调整TEAL/DONOR比、液相和气相聚合中的氢气浓度、气相组份和乙烯含量,使多相共聚物EPF30R具有良好的高刚性、流动性和冲击性能。     

红花黄色素提取工艺的研究

对红花黄色素提取条件进行了系统研究.以羟基红花黄色素A为对照品,选定水为最佳提取剂,实验确定红花黄色素的适宜提取条件为:浸取温度70 ℃,料液比为1∶100,浸取30 min,提取两次.     

基于重标极差法和神经网络的隧道变形趋势判断

为准确、科学及全面地对隧道变形进行趋势判断和预测分析,将隧道的变形过程划分为中期阶段和长期阶段,利用R/S分析对其位移序列和速率序列进行趋势判断研究,再利用PSO-BP神经网络对各阶段的变形进行预测,将预测结果与R/S分析结果进行对比,验证两者的一致性。利用两个工程实例进行检验,得出各序列的Hurst指数均大于0.5,说明各序列均具有持续变形的长期性,且位移序列的趋势性均大于速率序列的趋势性;同时,变形预测结果也显示隧道后期变形将持续增加,验证了R/S分析的准确性。     

氯霉素在聚茜素红薄膜修饰电极上的伏安行为及其测定

研究了聚茜素红薄膜修饰电极(PARE)对氯霉素(Chloramphenicol,CAP)的电催化作用,并应用于对微量CAP的定量检测。实验结果表明:在0.010mol/LHCl+1.0×10-4mol/LCu2++0.10mol/LNaCl测定体系中,CAP的浓度在1.0×10-9mol/L～1.0×10-8mol/L范围内与它的氧化峰电流呈良好的线性关系,线性方程和线性相关系数分别为:ip(μA)=-0.188×10-8CCAP(mol/L)-7.62,γ=0.9997,检出限可达5.0×10-10mol/L。CAP的标准回收率为95.9%~102.9%,八次平行样品测定结果的相对标准偏差3.2%。     

Glass transition and the rigid amorphous phase in semicrystalline blends of bacterial polyhydroxybutyrate PHB with low molecular mass atactic R, S-PHB-diol

The glass transition and the crystallinity of blends of isotactic bacterial PHB and low molecular mass atactic R, S-PHB-diols was investigated by means of differential scanning calorimetry (DSC), temperature-modulated DSC and dielectric spectroscopy. It was found that (i) T_g of crystallized blends is much lower than T_g of quenched blends, (ii) the semi-crystalline blends can only be described with a three-phase model. From the experimental results the amount of the oligomer component in the mobile amorphous as well as in the rigid amorphous phase was determined. It could be shown that the low molecular mass atactic R, S-PHB-diol is enriched in the mobile amorphous phase of the semi-crystalline blends, but 5-15% oligomer remains, however, in the rigid amorphous phase.     

Toughness Optimization of SBR Elastomers – Use of Fracture Mechanics Methods for Characterization

Elastomer materials are used in a wide application range and subjected to different loading from which failure of the material results. Because this failure is caused by initiation and propagation of cracks, the application of fracture mechanics methods for the assessment of the material is obvious. A short summary of the methods of technical fracture mechanics including possibilities of determination of crack resistance curves is given. Vulcanizates on the basis of SBR 1500 with various sulfur and carbon black contents were investigated. For describing the crack initiation and crack propagation behavior, several fracture mechanics examination methods were applied. Tear‐analyzer results were used to assess the crack propagation behavior under fatigue‐like loading conditions. Furthermore, for the characterization of the crack resistance of the materials under impact‐like loading conditions, instrumented tensile‐impact tests were performed. To obtain information about the initiation and propagation of a stable crack, quasi‐static fracture mechanics tests were applied. The results of the several tests are discussed in dependence on sulfur and carbon black contents. We found a non‐monotonous behavior of the toughness as a function of carbon black loading. An explanation is given in connection with a percolation‐like transition in filler morphology on larger length scales.

Schematic crack propagation curve for characterizing the fatigue behavior of the vulcanizates recorded in a TFA test.     

黄磷尾气净化脱除磷化氢、硫化氢中试试验

采用自制的催化剂JC-4,设计出碱洗-催化氧化工艺对黄磷尾气进行深度净化处理。中试试验结果表明:常压、100℃、尾气流量为36~50 m3/h、氧气体积分数为1.2%~1.5%时,PH3的脱除率接近100%,出口质量浓度低于1.0 mg/m3;碱洗单元可以除去90%的H2S,经过催化氧化单元可以进一步脱除H2S,净化效率接近100%,出口质量浓度低于1.0 mg/m3;催化剂经100~200 h需要再生,400 h后需要活化,再生和活化处理后的催化剂性能良好。     

基于R语言的机器人教育微博可视化研究

本文利用R语言对关注度不高、转发量不太大的机器人教育微博进行了可视化研究。在分析技术实现过程的同时,我们得出结论是:机器人教育的舆情由教育官方媒体和企业培训机构主导;经济力量决定着参与讨论的程度;微博不是学习内容交流的主阵地。     

二氧化钛固载杂多酸催化剂的制备及其光催化性能研究

采用浸渍法以TiO2为载体制备了固载型杂多酸光催化剂--H3PW12O40/TiO2,H8SiW12O42/TiO2,H7PMo12O42/TiO2.通过Hammett指示剂与紫外光谱相结合的方法测定固体杂多酸催化剂的酸度,分别考察杂多酸种类、浸渍时间、浸渍浓度、烧结方式、烧结温度对催化剂酸度的影响,并对所制备的催化剂进行了红外光谱和光催化活性测试.结果表明,杂多酸固载到TiO2的表面,得到了催化活性较TiO2更强的复合杂多酸光催化剂,其对酸性大红3R的降解率从纯TiO2的79%提高到91%.以磷钨酸水溶液浸渍TiO2,浸渍浓度为0.10 mol·L-1 ,浸渍时间为28 h,烘干温度为120℃,微波炉焙烧功率为650 W,烧结时间为40 min制得的催化剂活性最高.在HPA-TiO2光催化系统中,杂多酸显著加速电子从TiO2表面到O2分子的传递,改变了TiO2光催化反应历程,从而提高光催化效率.     

快固化、无收缩特种MMA-R17树脂在设备基础灌浆,锚固及修补中应用

本文介绍国外聚合物砂浆的性质和应用、施工配比及物理机械性能，供设计人员参考。