Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

New nanocomposite materials based on polymerization of [oligo(oxyethylene) methacrylates] in the presence of montmorillonite clay

Intercalation of poly[oligo(oxyethylene) methacrylates] onto sodium montmorillonite (MMT) clay has been investigated. A polymer–clay hybrid has been synthesized through intercalation of the monomer followed by its solution free‐radical polymerization. Eight polymer–clay hybrids were prepared using different weight ratios of clay, different oligo(oxyethylene) lengths and different proportions of crosslinker. Evidence of the development of nanostructures is obtained from scanning electron microscopy, and wide‐angle X‐ray diffraction studies support these results which show disappearance of the peak characteristic to d₀₀₁ spacing. In this hybrid MMT is dispersed homogeneously in the polymer matrix. © 2003 Society of Chemical Industry     

Water and salt permeability of reinforcement polymer‐gel composite membrane

The charged mosaic polymer membrane (CMM) without reinforcement and the composite charged mosaic polymer membrane (CCMM) with reinforcement were investigated in terms of salt and water transport (permeability). The composite charged mosaic polymer membrane (CCMM) with reinforcement showed a unique transport behavior such as preferential material transport L_p and ω. Water permeability coefficient, L_p and salt permeability coefficient, ω were estimated by taking account of active layer thickness of composite polymer gel. The L_p and ω values of CCMM with reinforcement were larger than those of CMM without reinforcement. On the other hand, the reflection coefficient of CCMM, σ, showed negative value, which suggested preferential material transport to solvent transport. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

二次电池电极基板用复合多孔金属材料的研究

介绍了一种复合金属多孔体的制备及其方法，首先以泡沫塑料为芯膜，经过导电化处理使其具有导电性，其次进行电沉积金属铁，再进行电沉积金属镍，经过热处理后可制备出复合金属多孔体。该复合金属多孔体用铁取代金属镍，其抗拉性能优于单质泡沫镍，同时可以降低制造成本，主要用于载体如电池电极。     

Quantification of the layer dispersion degree in polymer layered silicate nanocomposites by transmission electron microscopy

As the performance of polymer layered silicate nanocomposites strongly depends on their interior layer dispersion, quantification of the layer dispersion degree is needed. In this work, a new methodology was developed to determine the dispersion parameter D_0.1, based on the measurement of the free-path spacing distance between the single clay sheets from the transmission electron microscopy (TEM) images. Several examples of exfoliated, intercalated, and immiscible composites were studied. It was found that the exfoliated composites had D_0.1 over 8%, while that of intercalated composites were between 4 and 8%. In the case of intercalation, a high frequency peak appeared at a short spacing distance in the histogram, which was a characteristic of the intercalation, distinct from the exfoliation. The main utility of this TEM methodology is for the quantification of exfoliated or intercalated samples with small number of layers with stacks. The dispersion parameter D_0.1 below 4% was suggested to classify as immiscible. A unique advantage of the TEM measurement is that the dispersion degree of different fillers can be counted individually.     

硬质合金与铁基复合材料热等静压扩散连接

以烧结结态硬质合金和粉末态铁基复合材料为连接对象，研究了两种材料的热等静压扩攻连接工艺，获得了直接连接接头和加镍作中间过渡层的间接连接接头，考察了接头的结合界面形貌，界面的元素扩散和界面结合强度。     

Thin conducting polypyrrole film on insulating surface and its applications

An electrically conductive plastic material was obtained by the polymerization of pyrrole on insulating polymeric materials and nylon cloth impregnated with the oxidant by vapour phase technique, resulting in a uniform, smooth and adherent coating of conducting polymer having a surface resistance ranging from 200 Ω/□ to 20 kΩ/□, which makes it suitable for applications as an antistatic material.     

Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

Effect of the particle size ratio on the conductivity of conductor-insulator powder composites: Numerical simulation

A theoretical method for determining the percolation limit and effective conductivity of composites based on polydisperse mixtures of insulator and conductor powders is proposed. The effect of the particle size ratio between the insulator and conductor on the percolation limit and effective conductivity is studied. Numerical simulation of the microstructure, effective properties, and percolation limit in composites is discussed. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 31–40, 2007.