无机高分子絮凝剂聚硫酸铁合成条件的研究

实验研究了以工业硫酸亚铁及废硫酸为原料,分别采用NaClo_3、KClO_3、H_2O_2及(o_2+NaNO_2)为氧化剂成聚硫酸铁的条件。在以(O_2+NaNO_2)为氧化剂的合成过程中,发现添加微量助催化剂(型号为HG-1、HG-2和HG-3),对提高合成速度及反应过程的稳定性具有重大作用。     

PTA装置压力离心机冲洗新技术

分析了仪征化纤PTA装置压力离心机运转效果不佳的原因,提出解决方案,改造实施后取得了很好的效果。     

脱落酸、乙烯和赤霉素对豌豆苗采后品质的影响

为了解植物生长调节剂对幼苗类蔬菜采后品质变化的影响，用脱落酸、乙烯、赤霉素处理豌豆苗（Pisum Satu-vum L.）。结果表明：脱落酸和乙烯处理加速了叶绿素、蛋白质、可溶性糖含量的下降和纤维素含量的升高。而赤霉素处理则显著延缓了叶绿素、蛋白质和可溶性糖含量的下降和纤维素含量的增加。     

腐殖酸对烤烟根系生长和生理活性的影响

对腐殖酸和基肥混施进行了烤烟盆栽试验。结果表明 ,腐殖酸能有效刺激根系的生理活性 ,提高根系抗坏血酸氧化酶、多酚氧化酶等呼吸酶的活性 ,增强根系的活力 ,并能有效促进烤烟根系生长 ,根干重、体积和长度均有提高。     

从菜西瓜中提取果胶的最佳工艺研究

为确定从菜西瓜中提取果胶的最佳工艺条件,以山西省临汾市菜西瓜为材料,采用酸法进行了提取果胶的试验研究。正交试验结果表明:在萃取时间为45min的前提下,从瓜瓤中提取果胶的最佳工艺条件是加水量为原料重量的4倍,85℃下,添加原料重量0.3％的多聚磷酸钠,果胶得率可达2.03％;从外果皮中提取果胶,加水量为原料重量的4倍,75℃下,添加原料重量0.7％的多聚磷酸钠,果胶得率可达2.98％。     

Preparation, Characterisation and Catalytic Behaviour of a New TeVMoO Crystalline Phase

TeM_xMo_1.7O mixed oxides (M = V and/or Nb; x = 0-1.7) have been prepared by calcination of the corresponding salts at 600 °C in an atmosphere of N₂. A new crystalline phase, with a Te/V/Mo atomic ratio of 1/0.2-1.5/1.7, has been isolated and characterised by XRD and IR spectroscopy. This phase is observed in the TeVMo or TeVNbMo mixed oxide but not in the TeNbMo mixed oxide. The new crystalline phase shows an XRD pattern similar to Sb₄Mo₁₀O₃₁ and probably corresponds to the M1 phase recently proposed by Aouine et al. (Chem. Commun. 1180, 2001) to be present in the active and selective MoVTeNbO catalysts. Although these catalysts present a very low activity in the propane oxidation, they are active and selective in the oxidation of propene to acrolein and/or acrylic acid. However, the product distribution depends on the catalyst composition. Acrolein or acrylic acid can be selectively obtained from propene on Nb-free or Nb-containing TeVMo catalysts, respectively. The presence of both V and Nb, in addition to Mo and Te, appears to be important in the formation of acrylic acid from propene.     

Synthesis and characterization of new thermally stable poly(ester‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic dihydroxy compounds

A series of new alternating aromatic poly(ester‐imide)s were prepared by the polycondensation of the preformed imide ring‐containing diacids, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A model compound (3) was also prepared by the reaction of 2b with phenol, its synthesis permitting an optimization of polymerization conditions. Poly(ester‐imides) were fully characterized by FTIR, UV‐vis and NMR spectroscopy. Both biphenylene‐ and binaphthylene‐based poly(ester‐imide)s exhibited excellent solubility in common organic solvents such as tetrahydrofuran, m‐cresol, pyridine and dichloromethane. However, binaphthylene‐based poly(ester‐imide)s were more soluble than those of biphenylene‐based polymers in highly polar organic solvents, including N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide and dimethyl sulfoxide. From differential scanning calorimetry thermograms, the polymers showed glass‐transition temperatures between 261 and 315 °C. Thermal behaviour of the polymers obtained was characterized by thermogravimetric analysis, and the 10 % weight loss temperatures of the poly(ester‐imide)s was in the range 449–491 °C in nitrogen. Furthermore, crystallinity of the polymers was estimated by means of wide‐angle X‐ray diffraction. The resultant poly(ester‐imide)s exhibited nearly an amorphous nature, except poly(ester‐imide)s derived from hydroquinone and 4,4′‐dihydroxybiphenyl. In general, polymers containing binaphthyl units showed higher thermal stability but lower crystallinity than polymers containing biphenyl units. Copyright © 2005 Society of Chemical Industry     

Comparison of Lactic Acid Productivities at High Substrate Conversions in a Continuous Two-stage Fermenter With Cell Recycle Using Different Kinetic Models

The steady-state performance of a two-stage recycle fermenter with two different types (I and II) of configurations for staging was investigated numerically for the continuous production of lactic acid. In Type I the bleed broth withdrawn from the first stage is supplied to the second fermenter, and in Type II both filtrate and bleed broth from the first stage are introduced to the second stage. Using four different kinetic models taken from the literature, the effects of operating parameters on the overall lactic acid productivities and the overall substrate conversions are examined. At moderate conversions, productivities for Type I operation are found to be higher than those for Type II and for the single-stage system. In the case of high conversions close to complete consumption, Type II operation is more efficient than the Type I and single-stage systems. For 99% conversion and 40 kg m^-3 substrate feed concentration, productivities for Type II are predicted to be 14-74% higher compared to those for the single-stage system at the same bleed ratios.