HT-730改性酚醛-丁腈胶粘剂的研制

对酚醛-丁腈胶粘剂进行改性，添加5．0％的硅烷偶联剂，改善了酚醛-丁腈胶粘剂的工艺性能，提高了粘接强度，特别是降低了酚醛-丁腈胶对环境湿度的敏感性。研制的HT-730胶在环境湿度90％时仍有很高的粘接强度，同时老化性能和适用期并没有受到影响。     

汽车工业生产用热熔胶膜的研制

介绍了汽车工业生产内装饰复合材料用热熔胶膜的性能及其研制状况。这种热熔胶膜具有使用便捷,高效,生产、使用过程中没有污染的具有热熔胶膜的特长。     

汽车灯用热熔胶的研究及性能表征

介绍了生产汽车灯用热熔胶的各种原料及其在胶粘剂中所起的主要作用，为汽车灯用热熔胶原料的选择提供了参考。还介绍了汽车灯用热熔胶的制备过程和厂家所需的各种性能及其表征方法。通过选择适当的原料及配比，生产出性能优良并具有良好市场前景的产品。     

胶层厚度对拉伸试样应力分布影响的数值分析

运用弹塑性有限元法研究了胶层厚度对承受拉伸载荷的对接接头胶层内应力分布的影响．三维有限元法数值分析的结果表明，随胶层厚度减小，胶层中正应力SZ与剪应力SYZ的分布趋于均匀；而对正应力SY而言，胶层厚度为0．15mm时，其边缘峰值应力最低。     

Bulk and Interphase Effects in Aged Structural Joints

Although structural adhesives are becoming widespread in numerous applications, one important limitation at present is the long term behaviour of bonded assemblies under conditions of high humidity, especially at elevated temperatures. This study presents a comparison between bulk properties of a structural epoxy resin and its behaviour in a torsional joint consisting of a hollowed-out cylinder bonded to a plate—both substrates being in stainless steel. Exposure to ca. 100% relative humidity at 70°C leads to modification of the bulk properties of the polymer, notably reduction of its elastic modulus. Although this may explain some differences in behaviour of the torsional joint, premature failure is attributed to weaknesses in the interphase zone.

Auger Electron Spectroscopy (AES) has been employed to investigate both unbonded steel surfaces and fracture zones. Although prolonged exposure to water leads to a more extensive degree of (apparently) adhesive failure at the interface polymer/metal, AES has shown the presence of non-negligible quantities of carbon, attributed to residual polymer. Failure would seem to occur, at least partly, in a weak interphase of the polymer, near, but not at, the interface.

Various possible causes are evoked. For dry failure, residual polymer may be due to the topography of the metal surface and/or local modification of the adhesive during cure. In the case of aged joints, in addition there are potential effects due to swelling and differential stresses, secondary bond failure and molecular chain scission within the polymer, all provoked by the presence of water.     

Effects of apitong (Dipterocarpus spp.) extractives on bond strength development and curing rate of adhesives

Emulsion polymer isocyanate ( ), polyvinyl acetate ( ) and resorcinol-formaldehyde ( ) adhesives were used to produce single lap shear specimens using resinous and non-resinous apitong (Dipterocarpus spp.) timbers. Tests showed that joints made with highly resinous apitong were about 40% weaker than similar joints made with non-resinous apitong. The resinous apitong was treated with different solvents to yield five different extractives which were characterized by infra-red analysis. Apitong extractives were then added to and adhesives and joints made with buna (Fagus crenata), a timber known to be low in extractives and easy to bond. Joints prepared using extractive-containing adhesives were generally weaker than those made with the unmodified adhesives. RF adhesives containing extractives cured more slowly than unmodified . It is thought that the acidic nature of the extractives changes the pH of the system sufficiently to affect the curing mechanism     

五氯酚在厌氧生物体系中的降解及反馈作用

为探讨厌氧系统降解五氯酚(PCP)能力及PCP对厌氧系统的毒性影响,采用UASB反应器进行了PCP模拟污水连续流试验,考察了不同PCP浓度及负荷条件下系统对PCP和COD的降解去除规律,揭示了PCP对系统产酸相和产甲烷相影响状况.结果表明,在进水PCP含量从无到开始加入、PCP浓度提高以及PCP负荷提高3个冲击变化阶段,厌氧系统对PCP和COD的去除率均表现出先迅速降低后缓慢升高的变化趋势,运行稳定后PCP和COD的去除率分别达91.2%和83.5%以上.PCP对厌氧系统中微生物种群产生影响,使系统产酸菌由丁酸型菌群为主逐渐演替为丙酸型菌群为主,PCP对系统产甲烷菌活性产生明显抑制,甲烷产量由PCP加入前的12.1L/d降低至加入后的2.5L/d.     

多羟甲基酚多丙烯酸酯的合成及其耐温性能研究

本文合成了新型耐温活性预聚体多羟甲基酚多丙烯酸酯,并考察了pH值,丙烯酸量,反应时间、反应温度、催化剂用量等因素对反应产率的影响。测试了固化物的TCA和DTA及力学性能,并用红外光谱确认主产物。     

A Thermo-Mechanical Study of Some Epoxy Adhesives Subjected to Combined Dynamic and Static Stresses

The object of the present study was to investigate the effect of superimposed dynamic and static stresses on mechanical and thermal properties of some epoxy adhesives. It was found that combinations of shear creep and torsional oscillations, applied simultaneously to adhesive joints at temperatures within the glassy range of the adhesive, led to strengthening of the joints in shear and to an increase in the glass transition temperature of the adhesive. Similar loading stresses applied at temperatures close to the T_g of the adhesive, led to opposite effects on the above mentioned properties of the joints. The width of the glassy-rubbery transition of the adhesives increased, in the whole range of temperatures used in this study and for all epoxy compositions, as a result of subjecting the joints to superimposed dynamic and static stresses. The broadening of the glass transition was interpreted as a result of the stiffening of polymer network during the combined stressing experiments. A linear relationship was found between the area of endothermal peaks in the first DSC scan of specimens subjected prior to test to superimposed dynamic and static stresses at temperatures below T_g, and the shear strength of the joints. In agreement with this observation and with literature data, a linear relationship was revealed also between the glass transition temperature of the resins (measured in the first DSC scan) and the shear strength of the joints. Based on experimental observations and on some literature information, it was suggested that the strengthening of the joint, as well as the changes in thermal properties of the adhesives, are mainly due to physical processes, such as short-range orientation of network chains and an increase in intermolecular interaction between highly polar sites of the network. The possibility that superimposed stressing led to changes in chemical crosslinking was discussed but it seems that no such reactions occurred.     

CJ91胶粘剂在螺旋振动光整机中的应用

螺旋振动光整机槽内壁的橡皮保护层由于老化及磨损等原因出现裂口甚至脱落现象，严重影响设备的使用寿命和闸把壳体的外观质量。通过分析和试验筛选出螺旋振动光整机的理想胶粘荆——CJ91胶粘剂并介绍了粘接修补工艺。