秸杆材料用作草皮栽培基质的研究

本文介绍了秸杆毡的成型工艺 ,通过植物所需的水、肥料和空气三种因素对秸杆毡的化学和物理性能进行了研究 ,该材料可被用作草皮栽培基质     

分析型全蒸发器在啤酒挥发性成分测定中的应用

综述了分型全蒸发器技术在啤酒发酵过程中的应用状况，并介绍了分析型全蒸发器模型结构及与之配合使用的连续多分支管。     

Texture Changes During the Ripening of Port Salut Argentino Cheese in 2 Sampling Zones

ABSTRACT: Texture changes during ripening of Port Salut Argentino cheese for different sampling zones were studied. Compression relaxation tests were performed and results were analyzed using both Maxwellian and Peleg's models. Elastic equilibrium modulus obtained from the Maxwellian model decreased from 1.22 to 0.11 10⁴Pa during ripening. The constants derived from Peleg's model, k₁ and k₂, diminished with ripening time from 1.18 to 0.71 min and from 1.27 to 1.12, respectively. Asymptotic equilibrium modulus from Peleg's model decreased from 0.95 to 0.07 10⁴Pa during ripening. Rate parameters derived from a 1st order kinetics applied to both equilibrium moduli showed that the decrease was faster in the external zone (0.0846 d⁻¹) than in the central zone (0.0368 d⁻¹). The correlation between equilibrium moduli, salt concentration, moisture content, and maturation indexes was obtained with a determination coefficient of 0.76.     

Application of annexation principle of thermodynamic property of In-Pb-Sb and In-Bi-Pb melts

Based on the principle of annexation and phase diagrams, the structural units of In-Pb-Sb and In-Bi-Pb melts were determined, and their calculating models of mass action concentrations were formulated. Calculated results agree well with practical values, which in turn show that the models deduced can reflect the structural realities of corresponding melts and the principle of annexation is applicable not only to some binary metallic melts, but also to ternary metallic melts.     

石油测井仪器可靠性指标探讨

在分析常用可靠性指标及其应用现状的基础上，根据可靠性理论及石油测井仪器的特点。提出了石油测井仪器的可靠性模型。在探讨常用可靠性指标对石油测井仪器适用性的同时，提出将平衡稳定工作时间NWTURE和免维修测井井次NOLWNM作为石油测井仪器可靠性指标的思想；探讨了获取可靠性指标的途径。给出了推荐使用的石油测井仪器可靠性指标。     

绿色食品与绿色包装

介绍了食品绿色包装与环境保护的关系，探讨了食品绿色包装材料的选择及应用，食品绿色包装设计及市场价值等方面的内容。     

由光率体求导折射率及振动方向的新方法

从光率体出发，利用坐标轴旋转，导出了光在晶体中传播时折射率及振动方向的公式。     

一种有效的优化的多载波通信系统的功率分配算法

本文提出一种关于DMT系统传输纯数据流业务的最佳的功率分配算法，该算法使用了一种有效的表格查手工艺工和拉格朗日乘法器对分搜索办法，能够较快的收敛到最佳的功率点。同时，易于用硬件和软件实现。     

吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.