IF钢冷轧及再结晶初期微观组织的TEM研究

采用透射电子显微镜对不同压下量和再结晶初期的IF钢样品进行了研究．结果表明：无论是在较小形变量下还是在较大形变量下，形变不均匀性是普遍存在的；冷变形程度不同，织构组分不同，TEM形貌也不同；在再结晶的最初期，冷轧的形变组织演变为近乎等轴的亚晶，优先形成{111}〈uvw〉取向的晶核，晶核逐渐吞并周围的形变基体而长大，最终形成再结晶γ-纤维织构．     

Pheromone Disruption of Argentine Ant Trail Integrity

Disruption of Argentine ant trail following and reduced ability to forage (measured by bait location success) was achieved after presentation of an oversupply of trail pheromone, (Z)-9-hexadecenal. Experiments tested single pheromone point sources and dispersion of a formulation in small field plots. Ant walking behavior was recorded and digitized by using video tracking, before and after presentation of trail pheromone. Ants showed changes in three parameters within seconds of treatment: (1) Ants on trails normally showed a unimodal frequency distribution of walking track angles, but this pattern disappeared after presentation of the trail pheromone; (2) ants showed initial high trail integrity on a range of untreated substrates from painted walls to wooden or concrete floors, but this was significantly reduced following presentation of a point source of pheromone; (3) the number of ants in the pheromone-treated area increased over time, as recruitment apparently exceeded departures. To test trail disruption in small outdoor plots, the trail pheromone was formulated with carnuba wax-coated quartz laboratory sand (1 g quartz sand/0.2 g wax/1 mg pheromone). The pheromone formulation, with a half-life of 30 h, was applied by rotary spreader at four rates (0, 2.5, 7.5, and 25 mg pheromone/m²) to 1- and 4-m² plots in Volcanoes National Park, Hawaii. Ant counts at bait cards in treated plots were significantly reduced compared to controls on the day of treatment, and there was a significant reduction in ant foraging for 2 days. These results show that trail pheromone disruption of Argentine ants is possible, but a much more durable formulation is needed before nest-level impacts can be expected. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

铁素体球墨铸铁与20钢的闪光对焊

试验使用铁素体球墨铸铁和20钢的实心棒料进行了闪光对焊，通过改变次级电压4～8级，通电时间3～5s，观察其焊接接头组织的变化并测定其抗拉强度。结果表明，接头由三个区组成；当通电时间一定时，抗拉强度随次级电压的升高先减小后增大；当次级电压一定时，抗拉强度随通电时间的增加而增大。在次级电压为8级、通电时间为5s时，抗拉强度达最大值，为370．8MPa，是20钢母材的90.4％，是球墨铸铁母材的83.7％。     

基于Lab VIEW的小型汽油机磁电机点火提前角的测量

本文介绍了磁电机点火系统的点火提前角测量原理。对点火系统的点火信号和触发信号进行采集、调理，再用单片机进行处理，最后用LabVIEW进行点火提前角数据存储和显示。     

Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

Effects of Spatial Characteristics on Smart Antenna System with Uniform Linear Antenna Array

1IntroductionCurrently,smart antenna technology can greatly en-hance system performance and i mprove the system ca-pacity so that it has been considered as a keytechnologyinthe third generation wireless communicationsystems .The researches on channel model , beamforming algo-rithms and receive algorithms have been widely carriedout and a great many of proposition have beensubmittedtothe 3th Generation Project Partner (3GPP) . Fromthe viewpoint of link-level and system-level research,many asp…     

铁路桥梁横向振动模拟及适应快速行车结构型式的研究

针对铁路提速后出现的上承式简支钢板梁桥跨中横向振幅过大的问题,以羊楼司桥(L=32m单跨上承式简支钢板梁桥)为例进行实桥检测和数值模拟,建立车辆、线路、桥梁三者的联合模型,考虑轮轨接触力,应用MSC/DYTRAN大型结构分析程序进行车线桥动力相互作用的仿真分析。研究揭示我国用量最多的C62型货车以70∽80km/h的速度空载通过时,该跨度的钢板梁桥发生横向谐振的机理。此外,用该方法对32m跨长的组合梁结构进行桥梁动力特性及列车走行性分析,表明该结构满足提速货车和高速电动旅客列车走行的要求。研究结果对我国高速铁路桥梁建设和既有桥梁的改造具有积极意义。     

锰铬不锈钢在化工应用中的风险及对策

对聚丙烯二装置丙烯球罐液位计不锈钢螺栓失效的原因进行了分析,结合锰铬不锈钢(200系列)的性能和国内市场上的现状,分析了锰铬不锈钢在化工生产中应用的风险,提出了应对方法。     

管线钢的发展趋势及生产工艺评述

对超纯净管线钢、高强度高韧性管线钢、易焊管线钢和高抗腐蚀管线钢的发展趋势进行了论述，分别介绍了宝钢、武钢、鞍钢管线钢的生产工艺、技术开发、化学成分和力学性能，认为中国应研制开发在酸性环境下使用的管线钢和X70高强度高韧性管线钢，并为X80高钢级管线钢的前期研究工作做技术准备。     

Ennoblement of stainless steel in natural seawater – A new explanation

The ennoblement of corrosion potential (E_corr) of passive metal immersed in seawater was investigated with electrochemical technology and epifluorescence microscopy. The in situ observation showed that the bacteria number increased on the metal surface according to an exponential law which was in the same way with the ennoblement of E_corr. At the same time, the anodic polarization current of high‐Mo stainless steel decreased in the initial days. According to the mix‐potential theory and the characteristics of polarization curves of high‐Mo steel in natural seawater, the ennoblement of corrosion potential may be induced by the decrease of the passive current density.