铝合金牺牲阳极电流效率损耗的微观分析

探针（EPMA）和能谱分析技术(EDAX)，考察了铝合金牺牲阳极的显微结构和腐蚀后的边缘形貌，讨论了电流效率和显微组织之间的关系.结果表明：晶界腐蚀引起的晶粒脱落是铝合金牺牲阳极电流效率损耗的重要原因.      

含B4C中性盐浴渗硼工艺问题的研究

在含Ｂ４Ｃ中性盐浴渗硼的高温反应研究的基础上，对该盐浴存在的工艺问题进行了分析研究。指出了渗硼能力均匀性，工件表面腐蚀斑与玻璃体的关系，分析了老化盐致使工件清洗困难的成因。     

反应堆A0纯铝的点蚀模拟

测量A0纯铝在去离子水中的极化曲线用来模拟反应堆池壳的点蚀.研究表明A0纯铝在去离子水中很容易钝化.实验中用美国EG&G普林斯顿应用研究公司生产的273型恒电位/恒电流仪测量模拟孔电位,极化曲线表明模拟腐蚀坑处于钝化状态,即便是氧化膜破裂,腐蚀坑也发展得很慢.用pH计测量孔中pH的变化,并得到其工作曲线,此曲线表明带有氧化膜的点蚀坑坑内存在明显的酸化现象.并对A0铝池壳的服务寿命进行了估计.     

Formation of nanostructured YSZ/Ni anode with pore channels by plasma spraying

YSZ/Ni is the conventionally most used material for making the anode of a solid oxide fuel cell. Agglomerated nanostructured YSZ/NiO powders and plasma spray are applied to produce nanostructured YSZ/NiO coatings on porous support substrates. After reduction in an ambient atmosphere of 7% hydrogen and 93% argon at about 800 °C for 4 hours, a novel SOFC anode with nanostructured characteristics such as nano YSZ particles, nano Ni particles, nano pores and nano pore channels is produced. This new YSZ/Ni anode provides larger triple phase boundaries for hydrogen oxidation reactions. X-ray diffraction patterns of these YSZ/NiO coatings after 1 h of heat treatment at temperatures from 700 to 1100 °C are obtained and Scherrer analysis is conducted to study the effect of temperature on grain size. The results obtained from SEM, TEM, XRD and EDX measurements and analyses are presented in this investigation.     

深冷处理提高镀锌钢板点焊电极寿命的机理

为了提高镀锌钢板点焊电极寿命，作者提出了镀锌钢板点焊电极的深冷处理方法。采用不同深冷处理工艺参数处理了点焊镀锌钢板的Cr—Zr—Cu合金电极，用这些电极进行了镀锌钢板点焊电极寿命试验并与未深冷处理的电极寿命进行了比较。用扫描电子显微镜对深冷处理电极进行了背散射及面扫描分析，用X射线衍射法观测了深冷处理前后的电极晶粒度，测试了电极在深冷处理前后的电阻率。通过对深冷电极微观结构的观测及电极性能的测试，探讨了深冷处理提高镀锌钢板点焊电极寿命的机理。研究结果表明，深冷处理提高了镀锌钢板点焊电极基体的致密性，改变了合金元素的分布，细化了电极材料的晶粒，提高了镀锌钢板点焊电极的导电、导热能力及电极抗压渍变形的能力，从而提高了镀锌钢板点焊电极的寿命。     

卧式离心铸造汽缸套"黑斑"形成机理及预防措施

卧式离心铸造合金铸铁汽缸套"黑斑"是一种由合金成分和生产工艺等因素而造成的"夹层"石墨漂浮、比重偏析的综合缺陷.主要预防措施是强化冷却和将锰含量提高到2%.     

20CrNiMo牙轮牙爪锻造缺陷对力学性能的影响

KX-250三牙轮钻头上的牙轮牙爪可选用20CrNiMo钢锻造,但20CrNiMo牙轮牙爪在锻造过程中产生的缺陷严重影响产品的力学性能.为此对20CrNiMo牙轮牙爪进行质量跟踪,并对试样进行了力学性能的测试.结果表明：当锻造产生了白点和过热缺陷时,牙轮牙爪的力学性能明显下降,尤其是塑性指标和冲击韧度降低明显.为了防止这些缺陷的产生,还提出了一些对策,以提高牙轮牙爪的力学性能.     

金属阳极电解槽修订标准释义

对HG/T 2471-1993《隔膜法电解槽金属阳极涂层》和HG 2951-1988（原GB 9844-88）《隔膜法金属阳极电解槽制造技术条件》标准的修订版HG/T 2471-2001《电解槽金属阳极涂层》和HG/T 2951-2001《隔膜法金属阳极电解槽》进行了技术性解释。公布了按照HG/T 2471-2001《电解槽金属阳极涂层》要求对产品质量达标企业的型式检验结果。     

Synthesis of nano Sb-encapsulated pyrolytic polyacrylonitrile composite for anode material in lithium secondary batteries

A novel process was proposed to synthesize nano Sb-encapsulated pyrolytic polyacrylonitrile composite for anode material in lithium secondary batteries. The preparation started with the dissolution of SbCl₃ and polyacrylonitrile (PAN) in dimethylformamide (DMF) solution, followed by the addition of KBH₄ to reduce Sb³⁺ in the solution. The Sb composite was obtained by pyrolysis of the Sb/PAN mixture that precipitated out when the DMF solution was added by plentiful water. The TEM analysis showed that about 100-200 nm Sb particles were embedded by the pyrolyzed PAN, which provided a conductive matrix to relieve the morphological change of Sb during electrochemical cycling. As-prepared composite presented good cycleability for lithium storage. The proposed process paves an effective way to prepare high performance alloy based composite anode materials for high performance lithium-ion batteries.     

电化学溶解镁阳极制备纳米MgO粉体

该文以"牺牲"阳极溶解法在0.04mol／L(Bu4N)Br的乙醇和乙酰丙酮混合溶液中,电流强度控制在0.2A,电解镁片6h,制得纳米氧化物粉体MgO的前驱体Mg(OEt)2-x(acac)xo控制pH=8.0左右,将含有前驱体的电解液直接水解。水解产物经洗涤、干燥后于500℃煅烧2h,制得纳米MgOg粉体。采用红外(IR)、差热-热重分析(TG-DTA)、X-射线衍射(XRD)、电子透射技术(TEM)等手段对前驱体和纳米MgO进行了表征。结果表明:制备得到的纳米粉体呈单分散结构,平均粒径在12nm左右。用此种方法比较容易制得所需产物,是一种合成纳米氧化物的很有前途的方法。