“双储”模式下的节能控制在小区供水系统中的应用

根据城市居民对供水的可靠性、稳定性、经济节能性的需求,课题组提出了一种基于"双储"模式的供水系统,并按照本市德胜住宅小区的供水要求,设计了一套由储水池、气压罐、变频器、多台水泵机组等主要设备构成的全自动变频恒压供水系统.经过近半年的运行测试,系统有效地解决了传统供水方式中存在的问题,增强了系统的总体性能,有明显的节能效果.     

Ni-Cr-Fe-Si-B合金涂层及铝青铜基体熔合区组织的研究

采用钨极氩弧焊方法在铝青铜基体上施焊了Ni—Cr-Fe-Si—B合金涂层，并运用金相显微镜、扫描电子显微镜及能谱分析了喷涂层、熔合区及热影响区的组织形貌和成分分布。结果表明，喷焊时，在涂层与基体界面两侧各组元均发生了明显的扩散，Cu、Ni组元间可相互取代，基体融合区组织的基本组成仍为α (α γ2)，但同时也形成了Cu2FeAl7、NiAl3等新相，且融合区组织细小，涂层与基体间为冶金态结合。     

用PID控制弧焊逆变电源的试验研究

本文介绍了对逆变电源进行数字PID控制的原理和方法,分析了采样周期、PID参数及不同的焊接工况对控制特性的影响。试验表明,只要恰当地选择PID(或PI)参数,不仅能实现高精度的恒流控制,而且能使系统的动态性能显著提高。     

高压切割喷嘴冲击磨损的数值分析

以复用矿井含煤颗粒的水对高压切割喷嘴的磨损物理问题为研究对象,采用计算流体力学理论进行数值计算,分析讨论了质量浓度为10、15、20、25、30、40 mg/L条件下速度、剪应力、磨损的分布以及变化关系。计算、分析结果表明:磨损主要发生在出口部位和锥体的后半部份,入口部份和锥体前半部份磨损较小;入口部位、锥体部位磨损量、剪应力随质量浓度增加变化较小;出口部位磨损量在质量浓度为10～20 mg/L减小较快,超过20 mg/L后变化不大;出口部位流体速度、磨损量、剪应力与质量浓度间存在对应关系。煤粒入口速度与混合物速度相同、锥体部位煤粒流体速度低于锥体部位混合物速度(平均值)约79.4%;煤粒出口部位速度随质量浓度的增大而呈现先增加后减小的趋势,速度最大值发生在浓度20 mg/L。     

供水管网中压力真实值的批次平差算法

分析了测压点优化布置的意义及原则,并根据供水周期性,依靠数量有限的测压点压力数据,结合管网的水力计算,利用传统的平差原理,将测压点以外的其它节点压力进行真实性校正,推算出了管网各节点的真实压力值,实现了通过有限测压点数据对管网所有节点压力的全面了解。     

Effect of pressure on three catalytic partial oxidation reactions at millisecond contact times

The effects of pressure on reactant conversion and product selectivities in three catalytic oxidation systems have been examined at pressures between 1 and > 5 atm. Reaction was sustained autothermally near adiabatic operating conditions at temperatures of 1000°C with residence times over the noble metal catalysts between 10^–4 and 10^–2 s. The three systems investigated were (1) HCN synthesis over Pt-10% Rh gauze catalysts, (2) methane oxidation to synthesis gas (CO and H₂) over rhodium-coated monoliths, and (3) ethane conversion to ethylene over platinum-coated monoliths. We find that selectivities in all three reactions do not change dramatically with approximately a five-fold increase in pressure. This strongly suggests that free radical homogeneous chain reactions are not significant in these processes and that they can be operated reliably above atmospheric pressure. For the synthesis of HCN over Pt-10% Rh gauzes, the selectivity to HCN can be maintained above 0.75 at pressures up to 5.5 atm. Selectivities to synthesis gas (CO and H₂) from a methane-air mixture over a Rh-coated foam monolith at pressures up to 5.5 atm were maintained above 0.90. Over a Pt-coated foam monolith, the selectivity to ethylene from ethane-air and ethane-O₂ mixtures was independent of pressure up to 6.5 atm and conversion rose slightly although it was necessary to maintain constant velocity and residence time over the catalyst to avoid carbon formation.This research was supported by DOE under Grant No. DE-FG02-88ER13878.     

Alternating pressure control system for hydraulic robots

Hydraulics is a promising technology for robots. However, traditional hydraulic infrastructures are often large and power-inefficient, with large power sources that hinder mobility. In contrast, electro-hydrostatic actuators are relatively power efficient, but their cost and weight can be excessive in systems with a higher number of degrees of freedom. In this paper, we propose a new alternating pressure control system for hydraulic systems with a higher number of degrees of freedom based on an alternating pressure source system. In this system, the valves open and close in synchronization with a pump with sensor feedback, allowing either pressure or position in each actuator to be controlled independently. With the proposed system, a centralized pump can be used with simplified tubing and simple on–off valves. Moreover, we developed a dynamic duty ratio system that improves performance and reduces pump utilization time. The experimental results confirmed that both the position and pressure of each actuator can be controlled in parallel on a multi-degree-of-freedom system.     

Fabrication of Titanium Aluminides via Powder-Cored Wire Arc Additive Manufacturing: Microstructural and Mechanical Characterization

Herein, an innovative powder-cored wire arc additive manufacturing (PC-WAAM) process is proposed to fabricate γ-TiAl thin-walled intermetallic alloy. The metallography, phase composition, and mechanical properties at different thin-wall locations are characterized. The results show that the alternatively distributed layer-like microstructure composed of α₂ (Ti₃Al) and γ (TiAl) phases is obtained along the building direction. The content of α₂ phase exhibits the tendency of decreasing from the bottom to top region. This unique microstructure characteristic is closely related to the typical thermal cycling history during deposition. Moreover, the tensile strength and microhardness of the top region are lower than the middle and bottom region. In general, the current PC-WAAM technique shows promising capability of fabricating γ-TiAl intermetallic alloy with low cost. This work becomes a valuable reference for understanding the evolution mechanism of microstructure and paves the way for the flexible and customized additive manufacturing of γ-TiAl alloy.