换热器防腐蚀方法介绍

文章对换热器的不同保护方法进行了介绍 ,重点讨论了渗铝、渗锌两种方法。在室温～ 80℃自来水和 3.5 %NaCl水溶液中 ,与碳钢基体相比 ,渗铝层的电位发生了反转 ,因而在针孔部位会形成大阴极小阳极的局面 ,易发生点蚀 ;而在相同条件下渗锌层不出现上述点蚀现象 ,更适宜在换热器的应用     

合理选用过剩空气系数的重要性分析

通过分析过剩空气系数过大或过小时加热炉多方面的影响,强调了合理选用过剩空气系数的重要性,并提出了控制措施。     

铝活塞余热淬火和自然时效的应用研究

图 1所示的活塞试件 ,在开型时间为 5 0s～ 5 5s时 ,其表面温度为 (4 90± 5 )℃ ,可满足淬火要求。自然时效时间为 2 4天时 ,其机械性能可达到国标技术要求。这种新工艺有明显的经济效益。     

空分设备的酸性腐蚀及预防

以切换式换热器空分设备为例 ,分析了空分设备酸性腐蚀的原因、可能造成的危害 ,提出了预防措施。     

Effect of processing on in vitro digestibility of protein and starch in quinoa seeds

The in vitro digestibility of protein in raw quinoa assessed by an enzymic method was 78%, significantly ( P > 0.01 ) lower than that of casein, 91%, and also somewhat lower ( P > 0.01) than that of the raw washed quinoa sample, 83%. the process used to remove the outer layers of the seeds containing saponins increased the protein digestibility significantly ( P > 0.01), by 7%. Heat treatments increased protein digestibility over that of raw quinoa samples. Only the cooked sample treated for 60 min presented a slightly lower protein digestibility, 77%, than those obtained for other heat-treated samples.
The temperature, time and moisture used in cooking and autoclaving of whole seeds of quinoa did not improve starch digestibility significantly. the digestibility of the starch in the raw and precooked samples was 72 and 77%, respectively, after drum drying and about 64% after extrusion in both cases. Precooking at 60°C for 20 min does not improve the digestibility of the quinoa starch.     

Dislocations and flux pinning in YBa2Cu3O7

The dislocation structures of bulk textured and epitaxial thin film YBa₂Cu₃O₇ superconductors are examined. Correlations between increases in flux pinning and dislocation densities are noted. A model for flux pinning by individual dislocations is presented. This gives a treatment of strain induced effects and effects of normal state region interactions. It is shown that the values of pinning predicted are in line with experimental observations.     

Evaluation of influence of external magnetic disturbance on superconducting magnet taking conservation of linkage flux into account

External magnetic disturbance influences the quality of the image obtained with a magnetic resonance imaging (MRI) system because it causes magnetic resonance frequency drift. When a superconducting magnet in persistent current mode operation is exposed to external magnetic disturbance coil current varies to keep linkage flux constant. Conventional analysis is usually formulated with constant current and does not provide correct evaluation of drift of magnetic field in the magnet. This paper proposes a method of numerical analysis of magnetic field considering conservation of linkage flux in a superconducting magnet under a persistent current mode operation. This method is applied to evaluate drift of the magnetic field in a superconducting magnet for magnetic resonance imaging due to external magnetic disturbance. Analysis results show good agreement with the experimental results.     

导汽箱产生长裂纹和大面积凹陷原因分析、处理及预防对策

对硫酸废热锅炉锅筒内自然循环的导汽箱产生长裂纹和大面积凹陷的原因作了分析，提出处理该缺陷的方法，确保了锅炉的安全运行，并提高了蒸汽的品质。     

热强钛合金BT25组织与性能

介绍了前苏联航空发动机用热强钛合金（或高温钛合金）BT25的发展概况，并对BT25合金的成分特点、热处理强化优点等做了进一步阐述，给出了退火状态下的物理性能，在说明热强钛合金微观组织与力学性能关系的基础上给出了BT25合金的各种力学性能。     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.