Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

Ni对球墨铸铁热处理的影响

采用电子探针，图象分析仪、差质变分析仪和Ｘ射线衍仪定量研究了Ｎｉ在球铁中的分布和Ｎｉ铸态球铁组成相比例奥氏体中含碳量以及贝氏体转变ＴＴＴ曲线线的影响，结果表明，Ｎｉ在球铁中呈连续负偏析，其加入可以影响球铁组成上比例，并使粤氏体中含碳量和贝氏体转变孕育期期增加。     

余热利用系统多目标优化模型及应用

以炭黑生产中的余热利用系统为背景建立了余热利用系统多目标优化规划数学模型;阐述了模型的求解方法;给出了实例分析。     

Prediction of evaporation heat transfer coefficient and pressure drop of refrigerant mixtures

A study on the prediction of heat transfer coefficient (HTC) and pressure drop of refrigerant mixtures is reported. HTCs and pressure drops of prospective mixtures to replace R12 and R22 are predicted on the same cooling capacity basis. Results indicate that nucleate boiling is suppressed at qualities greater than 20.0% for all mixtures and evaporation becomes the main heat transfer mechanism. For the same capacity, some mixtures containing R32 and R152a show 8.0–10.0% increase in HTCs. Some mixtures with large volatility difference exhibit as much as 55.0% reduction compared with R12 and R22, caused by mass transfer resistance and property degradation due to mixing (32.0%) and reduced mass flow rates (23.0%). Other mixtures with moderate volatility difference exhibit 20.0–30.0% degradation due mainly to reduced mass flow rates. The overall impact of heat transfer degradation, however, is insignificant if major heat transfer resistance exists in the heat transfer fluid side (air system). If the resistance in the heat transfer fluid side is of the same order of magnitude as that on the refrigerant side (water system), considerable reduction in overall HTC of up to 20% is expected. A study of the effect of uncertainties in transport properties on heat transfer shows that transport properties of liquid affect heat transfer more than other properties. Uncertainty of 10.0% in transport properties causes a change of less than 6% in heat transfer prediction.     

The effect of temperature on the dynamic characteristics of heat-resistant thermoplastic composites

Two thermoplastic and two thermosetting fibrereinforced plastic composites were subjected to dynamic tests over a wide range of temperature, covering both cryogenic and hot environments. The thermal behaviour of each composite, as indicated by its dynamic mechanical properties, was assessed individually, and was compared collectively with that of the other composites.     

太阳能热水器内表面电刷镀锌

用电刷镀的方法,对尺寸为2000mm×1000mm×0.8mm 的 A_3钢板电刷镀锌保护层;并对影响镀锌层质量的因素进行了充分的研究。     

A Study of the Specific Heats of the Compounds in the Sm_2O_3-BaO-CuO System

By means of X-ray diffraction and adiabatic scanning calorimeter,the specific heatsof five compounds in the Sm_2O_3-BaO--CuO system,such as Sm_2BaO_4,Sm_2CuO_4,BaCuO_4,Sm_2BaCuO_5,SmBa_2Cu_3O_(7-x),from -150℃ to 800℃ have been measured.It is found that the specific heats ofthese compounds increase smoothly with the increase of temperature.     

管外上升R－113流体的沸腾换热试验

详细介绍了Ｒ－１１３流体管外上升流动的沸腾换热试验，包括试验台架、流量计和温度测量的修正，以及试验数据。拟合的换热关系式为ｑ＝５２８（Ｔｗ─Ｔｓ）１．３３。     

熔融还原炉内二次燃烧和传热

总结了熔融还原炉内二次燃烧和传热的研究成果，对于转炉采用二次燃烧提高废钢比也有借鉴作用。