Interdiffusion behavior of Hg in HgTe/CdTe superlattices grown on Cd0.96Zn0.04 Te (211)B substrates by molecular beam epitaxy

Double-crystal x-ray rocking curve (DCRC) and secondary-ion mass-spectroscopy (SIMS) measurements have been performed to investigate the effect of rapid thermal annealing on the interdiffusion behavior of Hg in HgTe/CdTe superlattices grown on Cd_0.96Zn_0.04Te (211)B substrates by molecular beam epitaxy. The sharp satellite peaks of the DCRC measurements on a 100-period HgTe/CdTe (100Å/100Å) superlattice show a periodic arrangement of the superlattice with high-quality interfaces. The negative direction of the entropy change obtained from the diffusion coefficients as a function of the reciprocal of the temperature after RTA indicates that the Hg diffusion for the annealed HgTe/CdTe superlattice is caused by an interstitial mechanism. The Cd and the Hg concentration profiles near the annealed HgTe/CdTe superlattice interfaces, as measured by SIMS, show a nonlinear behavior for Hg, originating from the interstitial diffusion mechanism of the Hg composition. These results indicate that a nonlinear interdiffusion behavior is dominant for HgTe/CdTe superlattices annealed at 190°C and that the rectangular shape of HgTe/CdTe superlattices may change to a parabolic shape because of the intermixing of Hg and Cd due to the thermal treatment.     

Experimental densities for compressed R134a

This paper reports densities of compressed R134a (1,1,1,2-tetrafluoroethane) determined by using a contiuously weighed pycnometer at 20 K intervals between 180 and 380 K at pressures from slightly greater than the vapour pressure to 70 MPa. The results are accurate to within ±0.1%. Saturated liquid densities derived by extrapolation from the experimental values agree with other reported values to within ±0.3%.     

Laser scanning path generation considering photopolymer solidification in micro-stereolithography

It is essential to automate the scanning path generation process to effectively implement the micro-stereolithography. However, a scanning path that is generated based only on a 3D CAD model introduces dimensional inaccuracies. In micro-stereolithography, the photopolymer solidification is affected by fabrication conditions, such as the optical properties (laser power, laser scanning speed, laser scanning pitch focusing condition, etc.) and material properties of the photopolymer. Thus, the photopolymer solidification phenomena must be considered when generating a laser scanning path. In this paper, a scanning path generation algorithm that uses 3D CAD data and considers the photopolymer solidification phenomena is proposed to improve the dimensional accuracy in micro-stereolithography. Multi-line photopolymer solidification experiments were performed for various laser scanning conditions to examine the photopolymer solidification phenomena. From these experiments, linear relations between the solidification length (width) and scanning length (width) were acquired and stored in a database. Subsequently, these data were utilized to compensate the scanning path of the laser beam. In addition, experiments for determining the layer thickness in the z-direction were performed and these results were also used in the scanning path generation algorithm.This research was supported by the Highly Advanced National Project (http://www.most.go.kr), which performs some of the National R&D Program, and sponsored by the Korean Ministry of Science and Technology under the contract project code M10214000116-02B1500-02010.     

3#大布袋收尘器更新改造方案的探讨

通过对3^#大布袋收尘器更新改造方案的对比分析，探讨适合工艺条件的最佳收尘器的选择途径。     

Effect of dose rate and length of storage on the ESR signal strength in irradiated chicken bone

One hundred and twenty-five pairs of chicken drumsticks were randomly allocated to one of five dose rates: 5, 10, 15, 20 or 600 kGyh-. The highest dose rate was obtained using a linear accelerator whilst the remaining dose rates were provided using a ⁶⁰Co gamma source. Each batch of 25 pairs was further divided into groups five of which were stored at 4°C for 0, 7, 14, 21 or 28 days. ESR spectroscopy was used to measure the intensity of the radiation-induced signal. There was a quadratic relationship between ESR signal strength and dose rate, which although statistically significant is unlikely to be of practical importance. The magnitude of the ESR signal declined by about 20% over the first 14 days of storage at 4°C and thereafter the decrease was minimal.     

冶金厂房钢吊车梁设计中一些问题的探讨

对双层翼缘板焊接工型钢吊车梁的某些受力特征、吊车梁的支座节点连接构造设计等进行了较详尽的分析,提出了满足冶金工业厂房大跨度、大吨位吊车梁系统受力和工艺要求的方法.     

屏蔽电泵运行中存在问题的分析与改进

对屏蔽电泵在非设计流量下工作存在较大的轴向力不平衡，造成前端轴承磨损严重进行了分析。在不降低效率的情况下，在屏蔽电泵的泵头加入平衡盘使轴向力得到平衡，并取得了满意的效果。     

Microscale and mesoscale discrete models for dynamic fracture of structures built of brittle material

In this work we present the discrete models for dynamic fracture of structures built of brittle materials. The models construction is based on Voronoi cell representation of the heterogeneous structure, with the beam lattice network used to model the cohesive and compressive forces between the neighboring cells. Each lattice component is a geometrically exact shear deformable beam which can describe large rigid body motion and the most salient fracture mechanisms. The latter can be represented through the corresponding form of the beam constitutive equations, which are derived either at microscale with random distribution of material properties or at a mesoscale with average deterministic values. The proposed models are also placed within the framework of dynamics, where special attention is paid to constructing the lattice network mass matrix as well as the corresponding time-stepping schemes. Numerical simulations of compression and bending tests is given to illustrate the models performance.     

Determination of the Coordinates of the Center of a Gaussian Beam by Means of a Matrix Photodetector Using a Weighting Method

A weighting algorithm to determine the coordinates of the center of a Gaussian laser beam projected onto a matrix photodetector is considered. The influence of the internal noise of the photodetector, the maximum brightness of the signal at the beam maximum, and the beam radius on the precision of the algorithm is investigated. Recommendations on image processing are presented.     

Polarity control of GaN epilayers grown on ZnO templates

We report the successful growth of Ga-polar GaN epilayers on O-polar ZnO templates pre-deposited on c-sapphire. Prior to GaN growth, NH₃ is exposed onto the ZnO template. The polarity of the GaN layers is confirmed by etching of the surface and by conversion beam electron diffraction (CBED), while the O-polar ZnO is confirmed by CBED. It is suggested that the NH₃ pre-exposure helps form a Zn₃N₂ layer, which possesses inversion symmetry and inverts the crystal from anion polar to cation polar.