黑土土壤质量演变初探I：不同开垦年限黑土主要质量指标演变规律

根据土壤质量的定义和研究方法 ,对黑土的主要质量指标演变规律进行初步研究。结果表明 :黑土的颗粒组成受开垦历史影响的程度较小 ,其质地没有发生显著变化 ;黑土的有机质、全氮、全硫和全磷随着黑土开垦时间的增加而不断降低 ;速效磷随黑土开垦时间的增加有增高的趋势。经过统计分析 ,黑土中粉砂(0.05～0.002mm)含量与细砂(0.25～0.05mm)和粘粒(<0.002mm)含量具有相关性,黑土有机质含量与全氮、全硫、全磷和速效钾具有明显的正相关。因此 ,初步认为黑土中粉粒和有机质含量可以作为土壤物理和养分方面的质量指标     

交联型聚醚聚氨酯的表征、力学性能及其碱金属盐络合物的导电性能

采用三羟甲基丙烷（ＴＭＰ）作交联剂与聚乙二醇（ＰＥＯ－１５４０）和甲苯二异氰酸酯（ＴＤＩ）反应，得到了具有较好力学性能的交联型聚醚聚氨酯（ＰＥＵ），该聚合物与ＬｉＣｌＯ４的结合物具有较高的室温电导率（σ３０℃＝１．８７×１０￣（－４）Ｓ／ｃｍ）。采用全反射红外光谱（ＡＴＲ－ＩＲ）对聚合物的结构进行了表征。对聚合物的组成、不同ＴＤＩ类型及络合盐浓度对聚合物力学性能及其络合物电导率的影响进行了探讨。低度交联聚合物的络合物，其电导率与温度的关系符合建立在自由体积理论上的ＶＴＦ方程，表明络合物中离子的传导主要是在无定形区域进行，与自由体积有关。     

DCS的评价与选择

本文综述了ＤＣＳ（集散控制系统）三代产品的总体水平评价，介绍了ＤＣＳ的总体性能、评价指标和它的选择准则。     

Ti-23Al-14Nb-3V合金氩弧焊接头的显微组织及其力学性能

研究了预热对Ｔｉ－２３Ａｌ－１４Ｎｂ－３Ｖ合金焊接性，特别是对消除氩弧焊冷裂纹的作用以及对接头显微组织和力学性能的影响。结果表明，焊前预热可有效降低该合金的冷裂倾向。经预热处理后，焊缝区的结晶层状线消失，热影响区的硬度峰得到缓和，整个焊缝的显微硬度分布趋于均匀，但焊缝区的枝晶发生粗化，热影响区有所扩大。焊件接头的拉伸试验表明，预热可使焊缝区的接头强度系数增加，但无论预热与否，接头强度均低于母材强度，且不显示宏观塑性。     

Analysis and visualisation with host-based software – The features of STNAnaVist™

This article is based on experiences with data and text mining to gain information for strategic business decisions, using host-based analysis and visualisation (A/V), primarily in the field of patents. The potential advantages of host-based A/V are pointed out and the features of the first such A/V software, STN^®AnaVist™, are described in detail. Areas covered include the user interfaces, initial set of documents for A/V, data mining, text mining, reporting, and suggestions for further development.     

Solar radiation climate in Malawi

Recently, Diabaté et al. [Diabaté, L., Blanc, Ph., Wald, L., 2004. Solar climate in Africa. Solar Energy 76, 733–744] created a map of solar radiation climate in Africa using clearness index for 62 sites. They established a solar climate class II located in Malawi and Madagascar. However, their analysis did not include any irradiation data from a site in Malawi. In this study, the solar radiation climate of Malawi has been studied using long-term global radiation data from a local site. The mean monthly (K_tm) and seasonal (K_ts) daily clearness indices for the site were computed. It is observed that K_tm has two maxima in a year (K_tm = 0.58 in May and K_tm = 0.64 in September), in close conformity with findings of Diabaté et al. (2004). Other results are presented and discussed.     

热强钛合金BT25组织与性能

介绍了前苏联航空发动机用热强钛合金（或高温钛合金）BT25的发展概况，并对BT25合金的成分特点、热处理强化优点等做了进一步阐述，给出了退火状态下的物理性能，在说明热强钛合金微观组织与力学性能关系的基础上给出了BT25合金的各种力学性能。     

网上协作学习模式研究

主要针对网上协作学习的基本模式、实现方式和存在的问题进行了初步研究。     

Control of structure and tack properties of acrylic pressure‐sensitive adhesives designed by a polymerization process

Free radical emulsion polymerization of methyl methacrylate (MMA) and 2‐ethylhexyl acrylate (EHA) results in the synthesis of pressure‐sensitive adhesives (PSAs) with good tack properties. Management of both the copolymer composition and the polymerization process allows one to control the behavior of the PSA. Semicontinuous (SC) processes create polymer particles whose instantaneous composition is close to that of the feed particle The SC Mixture process (continuous feeding with comonomer blends) affords nearly homogeneous latex particles and PSA films. The SC Gradient process (separate feedings at inversely varying rates) affords heterogeneous particles and films. The Batch process leads to somewhat heterogeneous films, but the hard (MMA‐rich) microdomains are made compatible with their soft (EHA‐rich) matrix because of the assumed formation of tapered‐type copolymers. Tack measurements indicate the importance of the particle and film structures. Too much hardness or softness leads to unacceptable lacks of adhesion and cohesion, respectively. Homogeneous structures prove adequate, but their tack properties collapse with rising temperature. Heterogeneous structures, with extensive phase segregation, prove unsatisfactory because they lack adhesion and cohesion. Finally, the association of well‐balanced composition and compatible heterogeneity is the criterion for suitable PSA behavior. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2749–2756, 2003     

A numerical model for induction heating processes coupling electromagnetism and thermomechanics

This paper presents a mathematical and numerical model developed for coupling the various physical phenomena (electromagnetic, thermal and mechanical) taking place in axisymmetrical induction heating processes. All three electromagnetic, thermal and mechanical models are time dependent and take full account of the electromagnetic and thermal non‐linear effect especially with magnetic materials. The electromagnetic problem is discretized and solved in the workpiece, air and inductors. The heat transfer equation and the mechanical equilibrium equations are solved in the workpiece only, both using a finite element method. The mechanical model can take into account thermoelastic–plastic behaviour for the part. The model has been successfully applied to several cases of induction heating. Comparisons between numerical and experimental results show an excellent agreement. Copyright © 2003 John Wiley & Sons, Ltd.