线加权余量法及其在正交异性板弯曲分析中的应用

利用有限差分法对控制方程和边界条件进行半离散化,使其定义在一些离散线上,然后采用加权余量法求解。这就是本文提出的线加权余量法,也可称之为有限差分-加权余量分维耦合法。文中以正交各向异性薄板弯曲平衡问题为例推导了有关具体算式,给出了数值算例,说明了本文方法的有效性。     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

几种高强度钢腐蚀疲劳裂纹扩展行为的研究

本文研究了ＧＣ－４，３０ＣｒＭｎＳｉＮｉ２Ａ和３００Ｍ超高强钢的腐蚀疲劳裂纹扩展行为。考虑了环境，热处理制度，应力比和频率对裂纹扩展的影响。研究结果表明：腐蚀环境和热处理制度对疲劳裂纹扩展有显著影响。在侵蚀性环境中随频率降低，裂纹扩展大幅度上升，随应力比提高，环境影响加剧。利用扫描电镜对试样断口形貌进行了分析，并讨论了高强钢的腐蚀疲劳机理。     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

微量Ag对CP276合金性能和组织的影响

研究添加不同含量的Ａｇ对ＣＰ２７６合金的拉伸性能和时效组织的影响。对拉伸强度、延伸率测试及透射电镜观察表明：０．１１ｗｔ％加入可促进Ｔ１相析出，使合金强度值升高；０．３５ｗｔ％Ａｇ的加入可在时效前期生成富Ａｇ、Ｍｇ的稳定的ＧＰ区，从而降低合金中Ｃｕ的固溶度，阻碍Ｔ１相析出，时效后期，ＧＰ区分解，生成大量Ｔ１相，使合金强度值显著升高。     

反向凝固法生产H90-钢-H90复合带

研究H90-钢-H90反向凝固复合过程中复合层厚度的变化规律以及复合带的组织和性能，探讨界面结合机理。结果表明：随着浸渍时间的增加，复合层的厚度变化经历了凝固生长、平衡相持和回熔3个阶段，钢带的预热温度越低，获得的最大复合层厚度越厚；H90复合层的组织为等轴晶粒，复合界面处Cu和Fe发生了扩散，而Zn未发生明显扩散，扩散层较薄，约为4μm；复合带的界面结合牢固；不同复合层厚度的复合带，其力学性能略有差异，但均达到GB5213——85所规定的F级深冲钢板的力学性能要求。     

人工神经网络技术在板料激光弯曲中的应用

基于人工神经网络基本理论,建立在板料激光弯曲中预测材料表面最高温度、弯曲角度的BP网络模型。借助于MATLAB仿真软件中的神经网络工具箱作为开发平台,将试验样本数据和经过试验验证的数值计算结果作为补充的样本数据用于BP网络的训练,利用训练好的BP网络对非线性的样本数据规律进行拟合,实现激光加工工艺参数的优化,为实际生产和加工提供有效的依据。     

Displacement Discontinuity Method for Fracture Mechanics Analysis of Reissner Plates: Static and Dynamic

This paper is concerned with the displacement discontinuity method applied to the shear deformable plates (Reissner’s and Mindlin’s theories) with cracks subjected to static and dynamic loads. Fundamental solutions of dislocation are derived using the Fourier transform method and the Laplace transformation technique. Boundary integral equations are presented in terms of rotations/displacement on the crack surfaces. The Chebyshev polynomials of the second kind are used to evaluate the integral equations with hypersingular kernels on the crack boundaries and determine the stress intensity factors at the crack tips. Comparisons are made with other numerical solutions to demonstrate the proposed method is accurate both for static and dynamic problems.     

不锈钢精密薄壁件外表面磁力研磨工艺研究

磁性研磨是一种利用磁场中的磁性磨料,对具有相对运动的工件表面进行光整加工的新技术。选择铝、镍、钴磁粉作为磁性磨料时,对奥氏体不锈钢精密薄壁件外表面具有良好的研磨作用。     

喷气纺纱质量影响因素探讨

简要分析了半制品质量对喷气纱强力和条干的影响，着重探讨了喷气纺纱机喷嘴压力、牵伸比、集合器宽度等对成纱强力和条干的影响。试验证明，提高半成品的质量、制定适宜的喷气纱工艺是改善成纱强力和条干的关键。