CFRP加固钢筋混凝土梁滞后应变计算方法

为了系统研究从零负载状态到满负载状态各个阶段CFRP片材加固梁滞后应变的计算方法,在充分考虑加固梁不同负载状态及受压区混凝土非线性本构关系的基础上,分别建立了不同负载贴片加固梁考虑混凝土抗拉作用时的滞后应变计算公式及不考虑混凝土抗拉作用时的简化计算公式.试验数据和对比分析结果表明:"考虑混凝土抗拉作用"公式的计算结果与试验数据吻合良好,计算误差<8%,明显优于现有文献的计算方法;"不考虑受拉区混凝土抗拉作用"公式的计算结果在混凝土开裂前和试验值相差较大,但对已裂加固梁的计算误差与"考虑混凝土抗拉作用"公式的计算误差接近.为简化计算,对未裂和已裂混凝土梁贴片加固时的滞后应变可分别采用"换算截面"公式和"不考虑混凝土抗拉作用"公式进行计算,两种简化方法的误差均不会超过10%.     

Surface performance of workpieces processed by electrical discharge machining in gas

The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.     

Electroless nickel plating on the surface of carbon fibers

The electroless nickel plating on the surface of carbon fibers was prepared by pretreating the carbon fibers in order to increase their conductivity,and consequently enhance the EMI shielding effectiveness of the composites.The relationship between the performance of depositing coat and pH value,temperature,reaction time and the way of agitation was studied.Results show that the depositing quality is stable under pH between 4.5 and 5.0,temperature between 75 ℃ and 85 ℃,reaction time for 10 min and air agitation.The uniform and compact nickel layer deposited on carbon fibers was proved by XRD and SEM,and the electrical resistivity of carbon fibers with nickel coating was tested.Results indicate that the electrical resistivity of carbon fibers with electroless nickel plating is decreased by an order of magnitude compared with that of carbon fibers.It means that nickel coating can greatly improve the electromagnetic interference shielding properties of carbon fibers.     

Relationship of hydrocarbon and source-rock in Nos.3-5 tectonic belts of the Lenghu area, northern Qaidam Basin

Based on analyses of the components of crude oil hydrocarbons and carbon isotopes, the content of normal alkane de-creased from 49.00% to 20.10% when moving from the No.3 to No.5 tectonic belt of the Lenghu area of the Qaidam Basin, while cycloalkanes increased from 30.00% to 52.20% and aromatic and branch chain alkanes increased gradually as well. The maturity of sterane in crude oil is higher than that of its source-rock, which shows that the hydrocarbons were generated from a deep source-rock of high maturity around the tectonic belts of the Lenghu area. The analysis of the characteristics of carbon isotopes also shows that these isotopes of hydrocarbon compounds in the No.4 and No.5 tectonic belt are apparently heavier than those in the No.3 belt. The results of our research show that the hydrocarbons in the No.3 tectonic belt are mainly from a relatively rich sapropelic substance, while the hydrocarbons in the No.4 and No.5 tectonic belt originated mainly from organic matter of a rela-tively rich humic type substance.     

二氧化硅负载支链有机膦的合成及其在二氧化碳催化氢化反应中的催化性能

以改性二氧化硅为核,利用发散法合成出二氧化硅负载的1～6代端胺基树枝状高分子(SiO2-PAMAM),样品经FT-IR,TG和端胺基分析表征.利用功能化载体表面的氨基与[Ph2P(CH2OH)2]+Cl-发生反应,合成出SiO2-PAMAM负载的有机膦(SiO2-PAMAM-PPh2),与三氯化钌复配成催化体系,考察了其对吗啉存在下的二氧化碳催化氢化反应的催化性能,该催化体系的催化活性(TOF)可达4 195.     

混合炭黑TST-103在轮胎内层帘布胶中的应用

研究了混合炭黑TST-103在轮胎内层帘布胶中的应用。小配合和车间大料及成品轮胎试验表明，使用8份混合炭黑TST-103，内层帘布胶的工艺性能、物理性能及实际使用性能均与原内层帘布胶相近，而每千克胶料成本降低了0．33元。     

Calculation of single adsorption isotherms from gravimetrically measured binary gas mixture adsorption isotherms on activated carbon at high pressures

A method is developed for the calculation of single-component adsorption isotherms from gravimetrically measured binary gas mixture adsorption isotherms at high pressures, at two temperatures and for different mole fractions of the gas phase. The adsorption of nitrogen/methane on active carbon Norit R1 is taken as an experimental example.     

不同线密度粘胶原丝及其碳纤维的结构性能对比

用Weibull分析处理 10mm长的 4种不同线密度粘胶原丝和相应碳纤维的单丝断裂强度 ,得到原丝线密度、强度分布和碳纤维强度的对应关系。采用透射电镜 (TEM )和小角X散射 (SAXS)分析粗旦原丝 ,发现孔洞较多 ,并存在大于 70nm的大孔洞。截面和表面照片也揭示出细旦原丝截面相对规整 ,表面较光滑 ,粗旦原丝则反之。结果表明 ,原丝线密度小 ,截面形状圆整 ,缺陷少 ,所制得的碳纤维强度高。     

Isosteric heat of sorption of CO2 in poly(ethylene terephthalate)

Sorption isotherms for carbon dioxide in poly(ethylene terephthalate) have been measured at 35–55°C. The isotherms were measured gravimetrically on a Mettler Thermoanalyzer-1 from vacuum to 1 atmosphere. The sorption data were used to generate sorption isotherms from which the isosteric heat of sorption of CO₂ in PET was determined. At 45°C the isosteric heat of sorption increases from −10 kcal/mole at a concentration of 0.5 cm³ (STP)/cm³ (polymer) to −8 kcal mole⁻¹ at a concentration of 1.5 cm³ (STP)/cm³ (polymer). It has been reported in the literature that the isosteric heat of sorption for this system decreased through a minimum before increasing with increasing concentration. Our measurement of the low-pressure sorption isotherms shows that this is not the case.     

Intergranular oxidation of silicon in 20Cr-25Ni niobium-stabilized stainless steel at 1140–1230 K

The kinetics of intergranular oxidation of silicon in a 20Cr-25Ni Nb-stabilized stainless steel are reported, at temperatures in the range 1140–1230 K, in CO₂ at 40 bar pressure. The depth of attack increased parabolically with respect to time, with an activation energy of 335±30 kJ/mol. The mechanism of growth is discussed in terms of classical internal-oxidation theories, and an alternative explanation based on an available-space theory is developed. The internal oxidation rates in a number of different alloys are compared with diffusivities of metals in the base alloy. It is proposed that intergranular oxidation in the 20–25 Nb steel is controlled by the rate of outward diffusion of iron or chromium in the alloy.