75m水头段混流式转轮水力性能研究

本简要介绍了７５ｍ水头段混流式转轮Ａ６１６和Ａ６４３的设计方法,并对试验结果进行了分析。     

YT62型液力偶合器故障分析及处理

针对YT62型液力偶合器在实际运行过程中经常出现的泵轮侧推力轴承温度偏高、泵轮和涡轮侧推力瓦块烧毁以及泵轮叶片断裂等故障进行分析及探讨,提出了改造偶合器泵轮侧推力瓦块定位盘,扩大泵轮侧径向推力轴瓦中分面的油槽通流面积,在断裂的泵轮叶片最接近180°对称的叶片上挖去和断裂叶片大小相同的部分,将转子动平衡校验后回装等处理方法和改进措施。改进后的实际运行效果表明,设备安全可靠性得到了很大提高,运行良好。     

Numerical Simulation on Effects of Pressure Distribution of Wind Turbine Blade with a Tip Vane

It is important to study the pressure distribution on the blade and in the adjacent area while searching the poweraugmentation theory with adding a tip vane to the wind turbine.This paper shows the CFD simulation relation-ship of the pressure distribution on the rotor blade and in the adjacent area,after calculating the pressure of thedifferent chordwise and spanwise point on the blade with the tip vane-V(8.8x8) and without the tip vane under tipspeed ratio λ4.5.Combining the isobaric section figure in certain location,it can be seen that the tip vane im-prove the pressure difference between pressure and suction surface.The most influenced zone is found and thesecan further display the power augmentation theory of the wind turbine using the tip vane.The simulation calcula-tion was based on N-S equations.3-D,steady,implicit solver was chosen.Turbulence model was k-ω SST.Dis-cretization scheme is SECOND ORDER UPWIND.Pressure-velocity coupling was a typical SIMPLE scheme.Inthe whole grid system,two-divided grid formation was adopted,that is,inner region and outer region.Inner re-gion including rectangular solid blade and neighboring,outer region is semi-cylinder.There were together720,000 nodes with tetra-prism unstructured mesh.     

9H级燃气-蒸汽联合循环机组主厂房结构设计方案研究

目的 针对9H级燃气-蒸汽联合循环机组主厂房结构设计方案研究,找出最佳的主厂房布置。 方法 通过结构型式、计算方法及设计参数取值进行优化,对技术、初投资、建设工期及施工组织等方面进行详细论述与分析。 结果 分析结果表明：钢筋混凝土结构与钢结构均为可行的,考虑经济性等诸多因素,推荐采用钢筋混凝土结构,屋面采用钢屋架。 结论 主厂房结构采用钢筋混凝土结构,屋面主承重结构采用钢屋架。     

300 MW机组变压运行方式的研究

针对300 MW机组运行经济性问题,通过试验测定了不同负荷下定压运行或变压运行时的供电煤耗、热耗、汽耗、汽动给水泵单耗、再热汽温等指标,并进行了对比和分析。结果显示,机组负荷在240 MW以下时采用四阀全开变压运行比较经济。     

M701F型燃气轮机的在线运行负荷特性

分析了重型燃气轮机负荷特性的影响因素,提出了研究重型燃气轮机负荷特性的技术路线。基于此,针对某M701F型燃气轮机,以国际标准化组织(International Organization for Standardization,ISO)的标准条件为基准,由机组的在线运行数据获得其负荷特性曲线,并建立负荷特性的数学模型。考察该燃气轮机6 940组实际数据,得出结论:当折算基准功率不小于18MW时,其负荷特性数学模型的最大相对误差不超过5.73%。     

An experimental study on self-output-control characteristics of micro downwind rotor with coning soft blades

In this short paper,we have treated the aerodynamic performance of micro downwind rotor with coning soft blades experimentally.The test wind rotor has the tip diameter of 1.5 m and three two-dimensional NACA0018 blades of 0.15 m chord whose material is light,soft and pliable foam plastic for perfect safety.From the wind tunnel test,it is realized that the performance is manageable by the coning angle of the rotor blade.In the present case,an improvement of the performance in lower wind speeds is achieved by...     

东北电网水电站水能利用情况分析

由于每一座水电站的情况不同,用耗水率很难对各水电站之间的水能利用情况进行比较,本文用“水能利用效率”对东北电网水电站的水能利用情况进行比较和分析,11座水电站多年平均水能利用效率为82．8％,堤坝式水电站高于引水式和混合式水电站,较客观地评价了各水电站的水能利用情况。     

轴流转桨式水轮机操作架强度分析

本文通过对轴流转桨式水轮机操作架的结构形式对比计算,初步得出影响轴流转桨式水轮机操作架强度的因素;同时,根据操作架的几何关系和受力特点,给出了比较合理的操作架结构形式,为今后的结构设计奠定了基础.     

混流式水轮机转轮简化模型焊接应力场的数值模拟

在确定混流式水轮机转轮简化模型、解决分段焊焊接热源加载问题及解决各独立实体间接触边界节点不重合的热传导问题的基础上,对转轮模型焊接过程的应力场进行了数值模拟.得到了焊接过程中纵向应力的演变规律与焊后应力场的分布情况.结果表明,焊后应力峰值出现在叶片与上冠或叶片与下环接触面附近.该结果可以较好地解释水轮机转轮叶片疲劳裂纹的产生和扩展的失效行为.