单片机控制的开环NC加、减速方法的实现

介绍了指数加、减速法,并采用等幅均匀的离散型,将指数形式离散化处理来实现步进电动机升、降速控制,给出了程序流程图和相关代码.     

Transitions from solid to liquid in isotactic polystyrene studied by thermal analysis and X-ray scattering

A three-phase model, comprising mobile amorphous fraction (MAF), rigid amorphous fraction (RAF) and crystalline fraction (C), has been applied to interpret the thermal transitions and structure of cold-crystallized isotactic polystyrene (iPS) from below the glass transition temperature, T_g, to above the melting point. Quenched amorphous iPS films were isothermally crystallized at different temperatures for 12 h. The fraction of crystalline phase, ?_c, was measured by differential scanning calorimetry (DSC), wide angle X-ray scattering and Fourier Transform infrared spectroscopy. The fraction of the mobile amorphous phase, ?_MAF, was obtained from the heat capacity increment at the glass transition temperature. In the three-phase model, the fraction of the rigid amorphous phase, ?_RAF, was found from 1−?_MAF−?_c. Specific heat capacity measurements by standard DSC confirm that the experimental baseline heat capacity conforms to a three-phase model for temperatures ranging from below T_g, up to the relaxation of RAF. The relaxation of RAF appears as a sigmoidal change in heat capacity accompanied by excess enthalpy, in which solid-like RAF is converted to an identical amount of liquid-like MAF.At temperatures above the relaxation of RAF, either one or two major crystal melting endotherms are observed in standard DSC, dependent upon crystallization temperature. However, using quasi-isothermal temperature modulated DSC, we always observed two reversing melting endotherms. The effects of annealing on iPS structure during the quasi-isothermal measurement were assessed using small angle X-ray scattering (SAXS). Combining the DSC and SAXS results, a model for the melting of iPS lamellae at low heating rates is presented.     

Experimental study on temperature stress calculation and temperature control optimization of concrete based on early age parameters

Temperature control curve is the key to achieving temperature control and crack prevention of high concrete dam during construction,and its rationality depends on the accurate measurement of temperature stress.With the simulation testing machine for the temperature stress,in the present study,we carried out the deformation process tests of concrete under three temperature curves：convex,straight and concave.Besides,we not only measured the early-age elastic modulus,creep parameters and stress process,but also proposed the preferred type.The results show that at early age,higher temperature always leads to greater elastic modulus and smaller creep.However,the traditional indoor experiments have underestimated the elastic modulus and creep development at early age,which makes the calculated value of temperature stress too small,thus increasing the cracking risk.In this study,the stress values of the three curves calculated based on the strain and early-age parameters are in good agreement with the temperature stress measured by the temperature stress testing machine,which verifies the method accuracy.When the temperature changes along the concave curve,the law of stress development is in consistent with that of strength.Under this condition,the stress fluctuation is small and the crack prevention safety of the concave type is higher,so the concave type is better.The test results provide a reliable basis and support for temperature control curve design and optimization of concrete dams.     

Dynamic buffering performance of the honeycomb paperboard filled with polyurethane

A new kind of composite buffering material was made by filling the voids of honeycomb paperboard with polyurethane. Drop tests were performed to evaluate the dynamic energy absorption capacity of the material. Based on the tests results, we analyzed the mechanical behaviors of the material under different conditions and obtained the inherent influencing laws of some factors on the material＇s dynamic buffering performance. It was shown that the dynamic buffering performance varied directly with impact velocity, and inversely with the void diameter, thickness and buffeting area of the composite material.     

第二代农民工市民化与中国共产党执政能力建设

第二代农民工市民化利益要求的实现有助于从阶级基础、群众基础、执政理念、执政资源和执政环境等方面加强党的执政能力建设。在第二代农民工市民化背景下,党应该强化执政为民的理念,构建利益相关制度,强化第二代农民工的工人阶级意识和主人翁意识,鼓励他们积极参与政治生活,有组织、有秩序地进行利益表达,使他们充分享受到城市经济社会发展成果,同时提高党自身的执政能力。     

析架空输电线路上倍容导线的选择

架空输电线路项目扩容改造,当采用倍容导线时,需在技术和经济上对倍容导线进行比较分析。文章对这种导线的种类、特性情况作了介绍,通过在220kV线路上对倍容导线的选择分析,为同类案例的处理提供了借鉴和参考。     

基于二维水流-水质数学模型计算的飞来峡水库动态纳污能力研究

根据飞来峡库区水动力特征,选取库区水功能区纳污能力设计条件,采用二维水流-水质数学模型计算确定了库区纳污能力,为库区纳污总量控制和制定限排总量提供依据。     

闸坝水力学特性的三维数值模拟

本文采用标准k-ε双方程紊流模型及基于水气两相流的VOF方法,运用FLOW3 D软件对闸坝进行数值模拟,得出不同水位下的闸坝泄流能力,以及不同部位的闸室及消力池水面线、流速、压力等重要水力学要素。结果表明数值计算在一定程度上可以达到模型试验的效果。     

环境经济系统工程的思考

环境问题与经济问题紧密相连,由于环境问题的综合性和复杂性,需要运用系统工程的方法和经济学原理,将环境问题置于整个经济系统中统筹考虑,建立相对完整的环境经济系统工程方法体系,将环境保护工作纳入经济社会发展中,使其成为决策中主要考虑的因素之一,并引起应有的重视。本研究从环境与经济承载力、环境投资的经济分析、环境与投资效率比较、环境资源的经济价值以及生态补偿与污染赔偿等方面构建环境经济系统工程的基本框架体系,并结合实际进行案例分析。研究表明,单纯的政府行政干预不如创造条件,如补偿、税收减免、投资、贴息等,使其具备在市场规则下.自动引导资源向环境保护与污染治理的投入,如排污指标的交易等。此外,自然资源是不可或缺的稀有资本,应该将保护生态系统及生物多样性纳入各级政府决策的主要方面。     

数据中心计算环境应用承载能力评价

随着新型计算服务模式在数据中心的普及,针对如何有效评价其承载能力的问题,提出一种新的应用承载能力评价体系和评价模型,具体分析了网络、计算资源对服务环境的影响度,并给出了实例分析。实例分析结果表明,新的评价体系和评价模型可以有效评估计算服务模式对各类信息服务系统部署运行的应用承载能力,进而提升信息服务保障整体效益。