Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

铝薄膜CMP影响因素分析

提出了在碱性抛光液中铝薄膜化学机械抛光的机理模型,对抛光液的pH值、磨料、氧化剂浓度对过程参数的影响做了一些试验分析。试验结果表面粗糙度的铝薄膜所需的最优化CMP过程参数:硅溶胶粒径为15～20nm,pH值为10.8～11.2,氧化剂浓度为2.5%～3%。     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

采用纯化学物质校准仪器测定钛合金中碳量

采用纯化学物质对高频加热－红外检测碳硫仪校准，对钛合金中的碳量进行测定。     

Formation and growth mechanism of TiC crystal in TiC_p/Ti composites

1　ＩＮＴＲＯＤＵＣＴＩＯＮＰａｒｔｉｃｌｅｓｒｅｉｎｆｏｒｃｅｄｔｉｔａｎｉｕｍａｌｌｏｙｍａｔｒｉｘｃｏｍｐｏｓｉｔｅｓ(ＴＭＣｐ)ｈａｖｅｗｉｄｅａｐｐｌｉｃａｔｉｏｎｆｉｅｌｄｓｆｏｒｔｈｅｉｒａｔｔｒａｃｔｉｖｅｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇ     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

纤维增强铝基复合材料变形损伤过程声发射研究

采用声发射（ＡＥ）技术，通过测定ＡＥ事件数、幅度和持续时间等发射特征参数以及恒载 Ｆｅｌｉｅｉｔｙ效应，对ＳｉＣ／Ａｌ和Ｃ／Ａｌ两类束丝纤维增强铝昨合在拉伸变形过程中的损失失效特征进行了分析探讨。实验结果表明，纤维种类、界面状况对复合材料损伤过程有着显著的影响，声发射技术是表征这类复合材料损伤特征很有潜力的方法。     

铝冷轧制油应用和生产工艺研究

通过对铝材冷轧工艺的分析。研究，以退火工艺中的斑痕为重点，提出采用加氢处理，异构化精制的石蜡基航空煤油组分为基础油，采用不同复合添加剂生产的通用铝冷轧制油完全可以满足客户要求。     

Chemical leaching and magnetic properties of non-equilibrium Al(Co–Cu) powders produced by rod milling

We report upon the chemical leaching and magnetic properties of nanoscale crystalline Al_0.6(Co₂₅Cu₇₅)_0.4 alloy powders produced by rod milling. X-Ray diffractometry (XRD), transmission electron microscopy, differential scanning calorimetry, vibrating sample magnetometry, and superconducting quantum interference device magnetometry were used to characterize the as-milled and leached specimens. After 400 h of milling, only the b.c.c. phase of the intermetallic compound γ-Al_3.892Cu_6.10808 was detected by XRD. After annealing the leached specimen at 600 °C for 1 h, the nanoscale crystalline phase was transformed into the f.c.c. Cu phase, and this was accompanied by a change in the magnetic properties. The peaks of the magnetization shifted towards lower temperature with increasing external field. The temperature behavior at T_f (45 K) for direct current (d.c.) magnetic susceptibility measurements was quite different for field cooling and zero-field cooling. After cooling the leached specimen from 800 °C, magnetization increased gradually.     

开关稳压电源用铝电解电容器的失效机理

概述了开关稳压电源用铝电解电容器的工作状态和失效模式，着重讨论了开关稳压电源用铝电解电容器的开路失效和击穿失效机理。