土钉支护在深基坑开挖中的应用

深圳某银行办公楼的深基坑支护采用了土钉支护，不但保证了施工质量，而且缩短了工期，减少了投资，以此工程为例介绍了土钉支护的土力学参数计算、结构设计、施工方案、技术措施和取得的显著效果。     

Simulation of the Forming Behaviour of a Boron Modified P91 Ferritic Steel

The forming behaviour at high temperature of a modified 9%Cr‐1%Mo (P91) ferritic steel containing B and Ti for elevated temperature service was investigated. The microstructure of the as‐received material is mainly martensite at room temperature, but special etching revealed prior austenite grains of about 25 μm in size. Torsion tests were conducted at temperatures in the range 850 to 1250 °C to simulate the hot rolling process under comparable conditions of temperature, strain rate and strain. The deformation data obtained from these tests were correlated with the Garofalo equation with a stress exponent of 4.6 and an activation energy of 315 kJ/mol. This equation was used to predict the formability behaviour for the rolling process and also to determine the maximum forming efficiency and stability of the steel. A temperature of 1200 °C is recommended to conduct the forming process.     

Cr12型模具钢锻造内部裂纹产生的原因及预防

基于Cr12型钢种的特点，归纳了Cr12钢锻造时内部裂纹的类型，分析了内部裂纹产生的原因并提出了相应的预防措施。     

钢纤维聚合物混凝土抗压本构关系

钢纤维聚合物混凝土是由聚合物混凝土基体和钢纤维共同组成的纤维增强复合材料，它的力学行为不仅依赖于聚合物混凝土基体的行为，而且与钢纤维的掺量、分散特征以及钢纤维的几何尺寸有关，本文将基于损伤力学原理研究在不同纤维掺量下的钢纤维聚合物混凝土的全程压力-应变曲线及其本构模型。     

不锈钢冶炼过程中相关热力学问题的解析(Ⅰ)--原料预处理时的热力学问题

针对“电弧炉 多功能转炉 VOD”三步法不锈钢冶炼工艺，以脱磷为主线，从冶金热力学的角度对流程中涉及的几个重要工艺环节的可行性(包括电弧炉去硅保铬、铁水包同时脱磷脱硫等问题)进行了理论分析和计算。在此基础上，提出了强化冶炼和脱磷的工艺措施，从而为不锈钢冶炼全流程控制磷及优化脱磷工艺提供了理论依据。     

宝钢曲轴用非调质钢的生产与展望

在实验室研究的基础上，开发了屈服强度为520MPa级的曲轴用微合金化非调质钢48MnV。工业生产了6000余吨φ151mm大规格圆钢，其各项性能满足了用户要求。指出了宝钢曲轴用非调质钢开发和努力的方向。     

烧结硬化用低合金钢粉

本文将介绍三种不同成分的低合金钢粉。在混入2 0%铜和不同石墨含量的条件下,对该三种粉进行了试验评定。试件的密度为6 9g/cm3,在氮氢混合气氛中于1120℃下烧结25min,在炉内冷却带650～400℃温区的冷却速度为0 4或1 5℃/s条件下,对烧结态和回火后试件的力学性能进行了测试。回火条件为200℃下保温60min。在一定的冷却速率和碳含量条件下,各种钢粉烧结后的硬度可高达40HRC。回火后,硬度仍可以保持在30HRC以上。     

Health promotion for women with physical disabilities: A pilot study.

Objective: To pilot test a health promotion intervention for women with physical disabilities. Design: Pre- and postintervention questionnaires. Participants: Two groups of women with physical disabilities (n=15). Intervention: Seven-session weekly workshop intervention grounded primarily in social-cognitive theory. Setting: Disability and rehabilitation settings. Main Outcome Measures: Indicators of health status. Results: Statistically significant positive changes between pre- and postintervention scores on measures of self-efficacy for dietary behaviors, medical decision making, social interaction, physical functioning, impact of physical limitation on role activities, and vitality. Conclusion: Women with disabilities who participate in this health promotion intervention may exhibit improvements on indicators of health status. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

西气东输工程用X70热轧板卷屈服强度检测值波动大的探讨

对西气东输工程用X70热轧板卷检验过程中出的屈服强度σ0.5波动大的情况进行了分析，认为拉伸试样弯曲是主要原因。这一问题可通过反复压平试样，确保试样的平直度以及适当提高钢的强度的方法加以解决。     

碳铬镍含量对高铬铸铁测温保护管性能的影响

通过高温氧化和高温磨损实验,研究了C、Cr、Ni 3个主要元素对高铬铸铁在高温条件下抗氧化和抗磨损性能的影响。结果表明:Cr含量越高,抗氧化性能和抗磨损性能越好;提高碳含量,明显提高高铬铸铁的高温抗磨性能;当w(Cr)=16％时,加入Ni能提高高铬铸铁的高温抗氧化性能;w(Cr)=30％时,Ni对高铬铸铁的抗氧化性能和抗磨损性能影响不明显.在1100℃以下,选用w(C)=2.8％,w(Cr)=30％、不加Ni的高铬铸铁铸造高温抗磨热电偶保护管,既有较好的使用寿命,又可降低成本.