直接氯化法合成对硝基氯化苄

介绍了以对硝基甲苯和氯气为原料 ,在催化剂存在下合成对硝基氯化苄的方法 ,考察了催化剂种类、反应温度、溶剂配比等因素对反应的影响 ,优化的反应条件为 :对硝基甲苯用量 1 3 7g,对硝基甲苯 /邻二氯苯 (摩尔比 ) =1∶ 0 .6,w (偶氮二异丁腈 ) =0 .6% ,反应时间 3 h,反应温度 1 60℃ ,产物单程收率大于 65 % ;将反应混合物中未反应的原料分离后 ,以无水乙醇为溶剂结晶纯化 ,物料 /溶剂 (摩尔比 ) =1∶ 1 .5时晶体含量在 99.0 %以上 ,结晶收率达 67     

New Reaction Engineering Concepts for Selective Oxidation Reactions

In order to enhance product yields in selective oxidation reactions, numerous reaction engineering concepts are being studied worldwide. Periodic operation has been investigated for decades, yet its application is limited to a few examples, such as the butane oxidation after DuPont or reverse-flow reactors for VOC removal. The use of microchannel reactors is a younger field, but it has already yielded promising results for process optimization. Catalytic wall reactors have proved to be a helpful tool for kinetic studies. On the laboratory scale, membrane reactors have displayed favorable behavior in selective oxidation. The Na vapor-catalyzed dehydrogenation of methanol to formaldehyde is a final example of an unusual new concept for selective oxidation.     

可再生烟气脱硫吸收剂及工艺研究

开发了一种新型可再生烟气脱硫吸收剂、解吸助剂及工艺。合成的吸收剂LDS对烟气中的SOx 具有良好的吸收和解吸能力 ,烟气中SOx 含量在 10 0 0～ 5 0 0 0 0 μg L范围内 ,脱硫率均可达 95 %以上 ;解吸助剂LDS A能有效提高主吸收剂LDS的解吸能力 ,提高单位吸收剂的吸收效率。试验表明 :该工艺脱硫率高 ,烟气净化效果好 ,与传统的烟气脱硫工艺相比 ,SOx 可回收利用 ,不产生二次污染     

α-蒎烯催化加氢反应的研究

以FYX - 2G型高压搅拌釜为加氢反应器 ,测定了在不同搅拌器型式和搅拌转速下高压釜的持气量和反应效果 ,认识到α 蒎烯催化加氢是外扩散控制的反应 ,当搅拌转速为 6 0 0r/min时 ,基本上能消除外扩散的影响。考察了Raney镍和Pd/C催化剂、反应温度在 35 3～ 499K ,压力在 4 0～ 10MPa的条件下对α 蒎烯加氢转化率和选择性的影响 ,结果表明Raney镍更适宜于α 蒎烯催化加氢 ,其转化率随温度、压力增加而提高 ,但选择性下降。采用温度 35 3～ 433K、压力 4 0～ 7 0MPa的操作序列 ,克服了α 蒎烯加氢转化率与选择性互为逆向的缺点 ,缩短了反应时间 ,制得了顺反比高达 18 2∶1的蒎烷 ,并且发现加氢反应从温度 433K开始有副产物对烷生成 ,当温度超过 45 6K时 ,加氢过程还出现飞温现象。     

甲基丙烯酸乙酯合成工艺研究

以大孔强酸性离子交换树脂为催化剂,甲基丙烯酸(MAA)与乙醇直接酯化合成甲基丙烯酸乙酯(EMA)。在MAA与乙醇摩尔比为1:3、反应温度89～93℃、空速0.3h~(-1)的条件下,MAA转化率不低于98％,EMA的选择性不低于99％。     

FCC原料掺入裂解焦油的研究及其机理分析

在催化裂化固定流化床小试装置上，对裂化原料中掺入富含芳烃的添加剂－裂解焦油进行了考察，确定了添加剂的最佳掺入量为1％，与不掺添加剂的裂化原料相比，其汽油产率提高，生焦量和干气产率减少，汽油选择性变好。同时通过对添加剂的原料体系的结构研究，对添加剂影响催化裂化过程的机理进行了探讨。     

催化裂化汽油选择性加氢脱硫催化剂RSDS-1的开发

介绍了用于催化裂化汽油选择性加氢脱硫催化剂RSDS-1的研究开发，考察了载体、活性组元、金属原子比以及助剂对催化剂选择性的影响。研究结果表明，催化裂化汽油中烯烃的加氢饱和受扩散限制；Co—Mo组合对烯烃饱和的能力相对较弱；较高的Co／Mo原子比有利于提高催化剂选择性；助剂的加入对催化剂选择性有明显的影响；RSDS—1催化剂用于催化裂化汽油选择性脱硫，对不同原料油适应性好，脱硫率可达80％，RON损失小于2个单位，且可长周期稳定运转。     

FeBP非晶态合金超细微粒的合成及其对PH3分解的催化作用

用化学还原法合成了FeBP非晶态合金超细微粒，用电感耦合等离子体光谱（ICP）、X射线粉末衍射（XRD）、透射电子显微镜（TEM）和差热分析（DSC）等手段对其进行了物性表征，并用微型催化反应装置考察了其对PH3分解的催化作用，结果表明，非晶态合金FeBP对PH3的分解具有良好的催化作用，能使PH3的分解温度从800℃以上降到500℃左右。490℃时分解率超过90％，540℃时达100％。     

Influence of nano-scaled dispersed second phase on substructure of deformed dispersion strengthened copper alloy

The deformation behavior of dispersion strengthened copper alloy Cu-Al2O3 was studied by TEM. The results show that nano-scaled dispersed second phase not only increases dislocation density in matrix, but also has an important influence on the dislocation substructure. The presence of fine dispersed Al2 O3 particles results in a uniform and random dislocation distribution in matrix copper and causes the difficulty in formation of dislocation cell structure and the decrease in the amount of cell structure during deformation. Deformation gives rise to much more dislocations and dislocation cells form more difficultly and the decrease in the cell size with the increase of dispersion degree.     

Terminal velocity of non-spherical particles falling through a Carreau model liquid

A procedure has been proposed for the estimation of the terminal falling velocity of non-spherical particles moving in a Carreau model fluid in the transition flow region. The procedure is based on a modification of the relationship formerly developed for the fall of spherical particles including the particle dynamic shape factor. The suitability of the proposed procedure has been confirmed by good agreement between experimental and calculated terminal falling velocity data. In the experiments, the terminal falling velocity of short cylinders and rectangular prisms in polymer solutions of different measure of shear thinning and elasticity has been measured.