机械研磨 Ni_(50)B_(50)合金形成非晶的过程

本文研究了机械研磨 Ni_(50)B_(50)合金非晶的形成过程。唯象地提出用 J-M-A 方程描述此过程,并作了简单的讨论。     

受干扰波相位测量的一种新方法

为了测量受噪声和谐波干扰的两个信号间的相位差，基于自适应带通滤波器（ABF）和测量信道交换技术，提出了一种新的测量方法。ABF采用可编程开关电容滤波器（PSCF）和锁相环，明显地抑制了噪声和谐波干扰，频率跟踪范围超过四个倍频程（0．5Hz-6kHz）。用微处理器控制4个开关来交换测量信道，可以基本上消除测量通道引入的附加相位移。两种方法结合提高了相位差的测量精度。实验说明了该测量方法的有效性，该方法也适合于被测信号为慢时变情况。     

一种适用于高数据速率和高速移动环境的新型信道估计方法——双正交通道信道估计方法

本文给出了一种适用于高数据速率和高速移动环境下的新型有效的信道估计方法-双正交通道信道估计方法(CETOC,Channel Estimation by using Two Orthogonal Channels),这种信道估计方法通过采用两个独立通道的联合估计,可以有效的克服快衰落的影响,从而使得在快衰落信道下应用多维状态调制成为可能.     

Influence of Coherent Flow Structures on the Dynamics of Suspended Sediment Transport in Open-Channel Flow

The influence of suspended sediments on coherent flow structures has been studied by simultaneously measuring the longitudinal and vertical components of the instantaneous velocity vector and the instantaneous suspended particle concentration with an acoustic particle flux profiler. The measurements were carried out in clear water and in particle-laden open-channel flows. In both cases, they clearly show the predominance of ejection and sweep phases that are part of a burst cycle. The analysis further demonstrates the importance of the ejection and sweep phases in sediment resuspension and transport. Ejections pick up the sediment at the bed and carry it up through the water column close to the surface. It is shown that ejections and sweeps are in near equality in the near-bottom layer, whereas ejections clearly dominate in the remaining water column. The implications of these results for sediment transport dynamics are discussed.     

非AWGN环境下调制类型自动识别

在非AWGN环境下，针对CW，AM，FM，OOK，PSK，QPSK，16QAM，FSK，MSK，SSB十种混合调制信号，对调制类型特征提取方法和自动识别算法进行了分析、综合、设计和计算机仿真。提出了梯层电平分析方法、频率瞬时信号分析、剔除载波的归一化能量分析、平方后信号的频谱分析、四次方后的信号频谱分析等方法。当SNR=10dB时，计算机仿真结果是正确识别率不低于95％，自动识别的平均处理时间为不超过10s。     

基于移动端多天线系统的无线衰落信道模型

根据当前无线移动通信对多天线移动接收端性能仿真的要求，讨论并建立了适于空时信号处理的移动端矢量信道模型。通过分析无线移动信道特点。研究了影响接收信号幅度相位的诸多因素，建立了相应的数学模型。并对随机参数选取进行了探讨。其中考虑到移动端接收信号到达角扩散的特点，采用GBSB椭圆模型产生了适于移动端接收信号仿真的随机角度，改进了一种瑞利衰落生成算法。最后信道的数值仿真结果符合理论和经验。同时，通过TD-SCDMA系统链路级仿真，也证明了该信道模型的有效性。     

ECAP细化晶粒法的仿真与分析

ECAP(Equal Channel Angular Extrusion)方法，是实现材料纯剪切变形的有效方法。本文采用有限元（FEA）分析软件ANSYS对Al的挤压过程进行仿真与分析。分析结果表明：外切角Φ、圆角半径、试样与凹模之间的摩擦系数、凹模本身的特性（如弹性模量、泊松比等）等等，对材料的变形量都有不同程度的影响。     

A Novel Channel Predictor Based on Constrained Hidden Markov Model

1　Introduction　Linkadaptationtechniqueisnowwidelyrecognizedasakeysolutiontoincreasethespectralefficiencyofwire lesssystems[1～ 3] .GPRS ,EDGE ,cdma2 0 0 0andWCDMAallincludelinkadaptationasameanstopro videhigherdatarates[4～ 5] .Torealizethepotentialoflinkadaptation ,reliablechannel predictionisneces sary[6 ] .　Therearemanydifferentchannelpredictionmethodsavailablenow ,suchasLongRangePrediction(LRP) [6 ] ,predictionbasedonsubspacesignalprocess ingalgorithms[7] ,predictionbasedonFinit…     

1960年前黄河下游河槽淤积物粒径组成分析

利用1999年汛前深层钻孔取样资料和历年淤积实测大断面资料分析出1960年前无三门峡水库影响的“自然”水沙情况下,下游河道主槽淤积物中d≥0.1 mm以上泥沙占50.7%,比1960-1999年大30个百分点,这种泥沙在下游的淤积比高达83.1%,比0.05 mm以上泥沙的淤积比高39个百分点。指出应在黄河中游寻找出0.1 mm以上的粗泥沙集中来源区作为近期水土保持的重点区域。     

Design of High Speed AWGN Communication Channel Emulator

This paper presents a method for designing a high accuracy white gaussian noise generator suitable for communication channel emulation. The proposed solution is based on the combined use of the Box-Muller method and the central limit theorem. The resulting architecture provides a high accuracy AWGN with a low complexity architecture for a digital implementation in FPGA. The performance is studied by means of MATLAB simulations and various complexity figures are given.