正交异性材料在R.Hill屈服准则下平面应力问题的特征场(h>2)

大多数金属材料在承载时产生了各向异性强化的特点,因此,对这一类材料特性的深入研究显得十分必要,正确建立及分析理论模型将对在实际工程中的应用提供很好的理论依据。本文在R.Hill屈服准则下提出了无量纲化的解析应力解,讨论了屈服参数2>h时,正交异性材料平面应力问题的应力场及应力特征场,利用应力微分平衡方程得到了决定特征曲线特征的参数。结果说明特征线一般互不正交。特别地分析了平头冲压边界附近的情况,得到了各应力状态不同区域的应力特征场,应用数值分析的方法对过渡区进行了计算。     

发动机扭矩与转速关系经验公式试验研究

在对发动机外特性曲线扭矩与转速实验数据分析的基础上，对原有的经验公式进行了分析、改进，提出了新的经验公式．由这一经验公式所计算的数值，在最大扭矩与最大功率点之间，可与实验数据拟合得很好．与原经验曲线相比，新经验曲线与实验曲线的离差可下降50％以上．     

节理岩体参数对围岩破损区影响的敏感性分析

本文针对黄河拉西瓦地下水电站工程，对节理岩体诸参数对围岩破损区范围的影响进行了敏感性分析。指出了主要敏感参数，对这些参数影响围岩破损区的趋势和可能程度进行了讨论，并对勘察和施工提出了一些意见。     

搅拌工艺对半固态Y112铝合金组织及性能的影响

采用自行研制的机械搅拌装置,研究了不同工艺参数对半固态Y112铝合金组织及性能的影响.研究表明,搅拌温度越高,搅拌速度越大,固相颗粒越细小、均匀和圆整,其抗拉强度与伸长率越高;但温度太高,固相颗粒会熔化,抗拉强度及伸长率也降低;随搅拌时间的延长,固相颗粒先变得细小、均匀和圆整,然后长大,抗拉强度、伸长率先升高后降低.     

Numerical study on PEMFC’s geometrical parameters under different humidifying conditions

Steady-state and three-dimensional simulations were carried out to study the influences of geometrical parameters on the performance of PEMFC under different hydrating conditions. Flow fields, species transport, transport of water in polymer membrane and movement of liquid water in cathode and anode porous layers were determined, in order to accomplish a complete estimation of ohmic and concentration losses of PEMFC power. The geometrical parameters were thickness of the polymer membrane, cathode catalyst layer as well as gas channel to rib width ratio. Every simulation was made under different relative humidities of inlet flows (50 and 100%) for every change of characteristic length. Results show that the influence of the geometrical parameters on ohmic and concentration losses is of considerable importance. The performance of PEMFC is seriously affected under dehydrating conditions. However, such performance may be considerably improved by using suitable geometrical parameters. Cathode and anode liquid saturation may not only affect the transport of species, but also the polymer electrolyte water content. These results show the importance of simultaneously calculating both the water absorption and desorption through the polymer electrolyte and the liquid saturation in the cathode and anode porous mediums to obtain an actual view of ohmic and concentration losses of the PEMFC performance.     

致密低渗透气田的试井特征分析--以新场气田为例

经对新场气田的试井资料处理,建立了不同类型储层典型井试井解释范例,得出低渗透试井判别式和判别图版,对该区具有低渗透特征的试井曲线进行了讨论。根据试井结果,可识别气藏(气层)储集类型,确定产层物性参数,为气藏动态分析提供基础资料。为开发致密低渗砂岩气藏、保持稳产高产奠定基础。     

准噶尔盆地腹部超压层分布研究

准噶尔盆地腹部普遍发育深层（大于4000m）超压系统，很多钻井都钻遇超压。通过对超压段钻井、地质、测井、地震特征系统研究发现，超压段泥浆密度大幅增加，具有高声波时差、低电阻率以及地震低速的超压响应特征。利用Dix公式计算地震层速度和利用Fillippone公式计算地层压力，得到超压数据体。准噶尔盆地腹部超压在白垩系及其以下沉积地层中均有分布，超压层的深度范围不同。分1井西凹陷边缘以及昌吉凹陷西南有空层现象。超压顶面分布的层位由北往南、从东到西逐渐变浅，从三叠系顶部到白垩系底部。深部超压对油气分布和富集有着重要的控制作用，准噶尔盆地腹部超压层分布的研究将对本区油气勘探起积极的推动作用。     

X射线三轴晶衍射法测量半绝缘GaAs单晶的化学配比

采用X射线三轴晶衍射法,根据As间隙原子对作为过量As在GaAs单晶材料中存在的主要形式的模型,可以无损、高精度测量半绝缘GaAs单晶的化学配比.并探讨了引起晶格变化的原因及其与熔体组分的关系,对于制备高质量GaAs单晶及其光电器件具有重要的意义.     

辽河流域平原区浅层地下水水化学特征和水质状况

本文根据多年地下水水质监测资料和近期实测监测资料,系统地对辽河流域平原区浅层地下水的水化学特征进行了分析,并对浅层地下水的水质类别及水质污染状况进行了分析评价.结果表明:平原区地下水化学类型以重碳酸盐型为主,浅层地下水有污染加重和扩大的趋势.     

Development of Low-Oxide MCrAlY Coatings for Gas Turbine Applications

Advanced high-energy plasma systems are being used to achieve the benefits of the high-velocity oxy-fuel (HVOF) system without losing the inherent advantages of plasma for coating of gas turbine parts. MCrAlY coatings play a very important role in the performance and reliability of gas turbine components. One of the important considerations for next generation of gas turbines, which have more demanding conditions and need to withstand ever increasing operating temperatures, is that they should possess very low oxygen content levels in the coating. Low oxygen content coatings are applied by the expensive low-pressure plasma spray (LPPS)/vacuum plasma spray (VPS) technique for critical components in aero- and land-based gas turbines. This work deals with the development of low-cost LPPS equivalent coatings (having low oxygen content) using the high-energy high-velocity plasma spray (HEHVPS) gun and inert gas shroud. A comparison has also been made with CoNiCrAlY coatings by HVOF.