The Change of Body Temperature During Convective Drying of Cube-Shaped Apple Pieces

When using the convective drying method, the mass transfer between drying air and moisture diffusion of the material is very important. The moisture moves inside the material because of the volume change caused by the increased temperature. This movement is additionally affected by the texture of the material. According to the research dealing with colloid capillary porous texture of vegetables and fruit, the humidity migration inside the material occurs in both fluid and steam condition at the same time. This migration is stimulated by the heating and decreasing humidity along with the flow. In this research, winter varieties of apples (Jonathan, Golden Delicious, and Idared) were studied by heating of a 20 × 20 × 20 piece of apple with a thermocouple in it. On the basis of the measurements it can be stated that for the fruits with a high percentage of moisture (75-90%), when making the drying condition, the moisture gradient is influenced by the fractured cells of the cut area. It was found that the variety of apple is very important in relation to the heating and water loss gradient. According to the results, the wet volume change due to the heating highly influences the water loss. The models that describe the temperature of the material have a connection with the water loss.     

Dynamics of hydrated iron(II) cations in nafion polymer membranes

Mössbauer studies of Fe²⁺ in water-soaked nafion polymer membranes in the temperature range between 90 K and 250 K have been performed. Above a critical temperature (～ 180 K) the spectra exhibit both elastic narrow absorption lines and quasielastic broad lines. These spectra are typical of bounded diffusion phenomena observed by Mössbauer spectroscopy in macromolecular systems like haemoglobin, myoglobin and ferritin. Similar spectral shapes have been observed by quasielastic neutron scattering from water in nafion membranes. Within 50 K above the critical temperature the total Mössbauer absorption area decreases by an order of magnitude whereas the narrow absorption line decreases by two orders of magnitude. The results are interpreted in terms of bounded diffusive motion of the iron. Using a model based on overdamped harmonically bound Brownian motion, the essential parameters of the iron motion can be derived as a function of temperature. The iron motion most probably reflects the motion of a large Fe²⁺ complex, e.g. Fe(H₂O)²⁺₆, which is attached to the polymer side chains via the sulphonic group.     

The effect of additives on the thermal stability of poly(vinyl chloride)

The effect of a range of organic additives on the thermal stability of poly(vinyl chloride), both with and without a chloroparaffin extender, was studied using a number of experimental techniques. Of the additives used the best overall balance was provided by pentaerythritol, which increased stability when the extender was present and had no effect when it was absent. The congo red test emerged as the most suitable technique, being consistent and inexpensive and able to screen several additives simultaneously. Isothermal differential thermal analysis correlated with the congo red test but required more expensive equipment, was time-consuming and demanded good mixing of the poly(vinyl chloride) compound to give reproducible results. Thermogravimetry was not sufficiently sensitive and the heat stability test was the least useful of all.     

Synthetic resins: XV. Chelation ion exchange properties of 2,4- dinitrophenylhydrazone of resacetophenone-formaldehyde resin

A number of copolymers were synthesised by condensing the 2,4-dinitrophenylhydrazone of resacetophenone with substituted benzoic acids/ phenols and formaldehyde in the presence of sodium hydroxide or hydrochloric acid. The decomposition temperature, solubility and viscosity of the polymers have been determined. The ion-exchange properties have been studied by using a batch equilibrium method. The distribution of a number of metal ions between an aqueous solution and the resin have been measured. A wide range of pH and variable ionic strengths have been investigated.     

用于重离子核反应实验测量的纵向电场气体电离室

本文报道了一种新型的大动态范围，多叠层探测器系统组件之一的纵向电场气体电离室的构造，性能和在中能得离子核反应实验中的应用。     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

Modelling of the extraction equilibrium of zinc from chloride solutions with tri-n-octylphosphine oxide

The extraction of zinc from chloride solutions with tri-n-octylphosphine oxide (TOPO) dissolved in benzene has been thermodynamically studied based on the law of mass action. A model employing the simplified Pitzer equations for stoichiometric activity coefficient estimations is found to be effective for the explanation and prediction of the distribution data, and the thermodynamic extraction constant is determined as log K_et = 5.16 ± 0.11 at 20°C.     

Influence of process variables on the drying of potato slices

Investigation of the effects of varying air velocity, slice thickness, and pre-treatment with sodium chloride solutions and surface active agents on drying potato slices indicated that the drying occurred entirely in the falling rate period and was controlled by the mechanism of liquid diffusion. The rate of drying, and therefore the diffusion coefficients, increased with the addition of sodium chloride and surface active agents. Diffusion coefficients were also influenced by air velocity and slice thickness, suggesting that the rate of drying of potato slices is controlled by a combination of internal and external resistances.     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.