CuMgAl类水滑石的制备和表征

用盐-碱制备法合成了CuMgAl三元类水滑石化合物。探讨了原料配比、合成方式、水热处理温度和时间对合成过程的影响,筛选出合成HTLcs的适宜条件,并对HTLcs结构的热稳定性进行初步研究。结果表明,制备HTLcs主要取决于pH值,同时由于Cu2+的姜-太勒效应,合成结构单一的CuMgAl类水滑石要求原料配比中n(Cu)∶n(Mg)不得超过1.0,CuMgAl-HTLcs热稳定性较差,300℃焙烧2h结构破坏,600℃开始烧结,在300~500℃之间,随焙烧温度提高所得复合氧化物比表面积增大,最高可达200 m2/g。     

Terminal velocity of non-spherical particles falling through a Carreau model liquid

A procedure has been proposed for the estimation of the terminal falling velocity of non-spherical particles moving in a Carreau model fluid in the transition flow region. The procedure is based on a modification of the relationship formerly developed for the fall of spherical particles including the particle dynamic shape factor. The suitability of the proposed procedure has been confirmed by good agreement between experimental and calculated terminal falling velocity data. In the experiments, the terminal falling velocity of short cylinders and rectangular prisms in polymer solutions of different measure of shear thinning and elasticity has been measured.     

粘土矿物用于乙烯聚合催化剂的研究 Ⅰ.以凹凸棒石粘土为载体的乙烯聚合催化剂

研究了以凹凸棒石粘土为载体,负载TiCl4制备的乙烯聚合催化剂的结构、性能及制备规律。结果表明,催化剂中Ti的负载量随焙烧温度的提高而逐渐降低,聚合活性随焙烧温度的提高呈上升趋势,但过高的焙烧温度也会导致粘土晶体结构的彻底破坏而不利于活化粘土活性的提高;通过采用烷基铝等有机金属化合物处理粘土同样可以极大地改善粘土性质,提高催化活性。不同助催化剂对以凹凸棒石粘土为载体的催化剂的聚合性能有较大影响。     

Water‐Stable,Magnetic Silica–Cobalt/Cobalt Oxide–Silica Multishell Submicrometer Spheres

A method to produce monodisperse magnetic composite spheres with diameters from less than 100 nm to more than 1 μm in water solution is reported. The spheres consist of a dielectric silica core and a cobalt/cobalt oxide shell which can be protected from further oxidation with an outer shell of silica or, alternatively, they can be covered with the polymer polyvinylpyrrolidone as a stabilizer. The formation of a uniform magnetic shell proceeds with the adsorption of metallic cobalt seeds, produced by the reduction of cobalt chloride with sodium borohydride, on a self‐assembled layer of polyelectrolytes on the silica core. In the second step, an outer silica shell can be formed by the hydrolysis and condensation of (3‐aminopropyl)trimethoxysilane and tetraethoxysilane. The double‐shell composite spheres show excellent sphericity, monodispersity, and a magnetic hysteresis loop at room temperature.     

Electrochemical Aspects of Electroosmotic Dewatering of Clay Suspensions

An attempt is made to elucidate the electrochemical aspects of the electroosmotic dewatering (EOD) of clays as reported in some recent work, especially that on interrupted DC power electroosmotic dewatering published by Rabie, Mujumdar and Weber (2). These authors showed that the dewatering by EOD stops after the DC power has been on for several minutes or hours; on interruption of their power and on short-circuiting of the electrodes, conditions can be created again for some further dewatering by DC power EOD. This discovery, of Rabie et al. is interpreted as a fuel cell effect and it is shown that it affords clues to several other electrochemical strategies for the possible enhancement of the efficiency of the EOD by DC power.

Further, the open circuit potentials observed by Rabie et al. (2) on the interruption of DC power are given an electrochemical interpretation which leads to quantitative estimates in agreement with the experimental values.     

Ultrasound‐activated Knoevenagel condensation of malononitrile with carbonylic compounds catalysed by alkaline‐doped saponites

α,β‐Unsaturated nitriles have been synthesized by Knoevenagel condensation of a carbonylic compound with malononitrile, assisted by sonochemical irradiation. Two alkaline‐promoted clays (Li⁺‐ and Cs⁺‐exchanged saponites) have been employed as catalysts. The influence of the carbonylic compound (benzaldehyde or cyclohexanone) and the use of a solvent on the catalytic activity have been studied. Remarkable increase in the conversion values has been found when the reaction is activated by ultrasound, as compared with the thermal activation. In this green, solvent‐free procedure, α,β‐unsaturated nitriles have been produced in very high yields (97%) when the Cs⁺‐saponite is used as catalyst. Copyright © 2004 Society of Chemical Industry     

Iterative finite element model of nonlinear viscoplastic analyses for blended granular porous media

The iterative finite element model, in which an element is used to represent a single particle, is generated to analyze the global behavior of multiple-material aggregates of materially nonlinear viscoplastic particles. The generalized Maxwell model is used to define four types of specific nonlinear viscoplastic materials, which are the elasto visco-plastic matter with linear viscosity, the plasto visco-plastic material with linear viscosity, the elasto visco-plastic media with nonlinear viscosity, and the plasto visco-plastic media with nonlinear viscosity. The theory and relevant penalty iterative algorithm are developed to analyze the four representative mixed granular systems consisting of materially nonlinear viscous particles. To verify precision of stress calculation, solutions of an axis-symmetric radial flow problem are compared with results of the literature and they are in a great agreement. The results present here provide significant insight into the fundamental behavior of granular media under compaction conditions, including prediction of the overall aggregates stress-strain response.     

硫化锌纳米粒子的微乳液合成

介绍了微乳液制备纳米粒子的基本原理。对影响微乳液体系形成的主要因素如油相、水相、表面活性剂种类及用量等进行了研究，以表面活性剂TWEEN80和SPAN80作乳化剂，通过调整其比例控制乳化剂的HLB值，制备了乳化剂浓度为0.3mol/L、水/乳化剂比为6：1的W/O型庚烷/ST80/水微乳液体系。在此微乳液中制备了ZnS纳米粒子，采用TEM和XRD对超细样品的结构进行表征，表明得到的样品为β型立方晶系ZnS粒子、粒子粒径10-30nm。     

n-Al2O3P/Ni复合刷镀层的组织和摩擦磨损特性

研究了镍基纳米Al2O3复合电刷镀层（n-Al2O3^p/Ni）的组织特征及擦磨损特性，并与快镍刷镀（Ni)进行了比较。结果表明：n-Al2O3^p/Ni复合刷镀层表面粗糙度更小，组织更致密，镀层摩擦系数随镀液中纳米粒子含量增加稍有增大；n-Al2O3在复合刷镀层中弥散分布，与基相良好结合；复合镀的耐磨性能明显优于Ni刷镀层，镀液中n-Al2O3含量为20g/L时，复合刷镀层具有最佳耐磨性能。