A parallel and scalable algorithm for ADI method with pre-propagation and message vectorization

It is hard to implement the ADI method in an efficient way on distributed-memory parallel computers. We propose “P-scheme” which parallelizes a tridiagonal linear system of equations for the ADI method, but its effectiveness is limited to the cases where the problem size is large enough mainly because of the communication cost of the propagation phase of the scheme.

In order to overcome this difficulty, we propose an improved version of the P-scheme with “message vectorization” which aggregates several communication messages into one and alleviates the communication cost. Also we evaluate the effectiveness of message vectorization for the ADI method and show that the improved version of the P-scheme works well even for smaller problems and linear and super-linear speedups can be achieved for 8194 × 8194 and 16,386 × 16,386 problems, respectively.     

MSP-G320240DBCW-211N大规模点阵式LCD与PIC单片机接口技术

介绍了大规模点阵式液晶显示器MSP-G320240DBCW-211N的特点及其与PIC18F6620单片机的接口技术，提出了应用过程中可能遇到的问题和解决方法．给出相关的C程序设计并在研制的智能光电检测仪器上得以成功地应用。     

Fracture toughness of thermoset composites reinforced by perfectly bonded impenetrable short fibers

The fracture toughness of brittle thermoset resins could be improved significantly by perfectly bonded tough, short fibers through both crack trapping and bridging effects. In this paper, the crack trapping effect was studied through the analysis of the change of strain energy associated with the crack propagation across a regular array of fibers, and the bridging effect was discussed based on the Andersson–Bergkvist model. The fracture resistance increases with the fiber volume fraction, and is independent of the elastic properties of the matrix, the crack length, and the cross-sectional diameter of the fibers.     

中国首创五大新兴智能基础学科的交叉应用与展望

可拓学、灰色系统、界壳论、集对分析和消错学这五大新兴智能基础学科都是我国首创的理论。本文首先简单介绍了五大学科，随后给出了五大学科的关系矩阵并讨论了其交叉应用的发展概况，最后对其交叉所产生的空白领域追行了初步的探讨，然后对其未来发展进行了展望。     

The stiffness matrix in elastically articulated rigid-body systems

Discussed in this paper is the Cartesian stiffness matrix, which recently has received special attention within the robotics research community. Stiffness is a fundamental concept in mechanics; its representation in mechanical systems whose potential energy is describable by a finite set of generalized coordinates takes the form of a square matrix that is known to be, moreover, symmetric and positive-definite or, at least, semi-definite. We attempt to elucidate in this paper the notion of “asymmetric stiffness matrices”. In doing so, we show that to qualify for a stiffness matrix, the matrix should be symmetric and either positive semi-definite or positive-definite. We derive the conditions under which a matrix mapping small-amplitude displacement screws into elastic wrenches fails to be symmetric. From the discussion, it should be apparent that the asymmetric matrix thus derived cannot be, properly speaking, a stiffness matrix. The concept is illustrated with an example.     

双重孔隙介质油藏中的吸渗排油作用

利用美国SSI公司研制的COMPN模拟软件对双重孔隙介质油藏一种重要的开采机理 吸渗排油进行了模拟研究,考察了一个基质岩块为四周裂缝所包围时.在驱动压力和毛管压力的不同平衡(驱动压力和毛管压力的相对大小)关系下的水驱油采收率和水驱油效率的变化规律.     

一种新型基于石英的热光型光开关

一种采用基于石英的平面光波回路技术（PLC）制造的热光型光开关正越来越引起关注，它具有低耦合损耗、高稳定性及适于大规模集成等优点。首先描述了采用热光相移器构成马赫-曾德于涉仪（MZI）结构的热光型光开关，然后讨论2×2MZI热光型开关的工作原理及基本特性，最后介绍了由2×2MZI热光型开关单元构成的大规模光开关阵列以及一种采用悬梁式结构热光相移器的低功率消耗的光开关。     

The effect of particle distribution on damage formation in particulate reinforced metal matrix composites deformed in compression

Image analysis results are reported on the generation of damage in particulate reinforced metal matrix composites during compressive deformation. The technique allows the automated collection of data on the incidence of particle fracture and void formation in the matrix as a function of important microstructural parameters such as local particle volume fraction and particle size. There is a strong relationship between damage and the local volume fraction of the reinforcement proving that damage formation is accentuated in regions of particle clustering. With the SiC reinforced materials examined, there was observed to be a change in dominance of damage mechanism from particle fracture at low local volume fractions to void formation in the matrix within strongly clustered regions. The results are compared with finite element (FE) modelling of the compressive deformation of clustered particles using a simple cluster of equi-spaced particles. The FE results suggest that plastic flow is generally inhibited in clustered regions. In certain highly clustered configurations shielding is such that flow does not occur in the heart of the cluster even at high levels of average plastic strain. The modelling suggests that the change in dominance of damage mechanism is related to the dramatic increase in tensile hydrostatic stresses in the matrix with higher levels of particle clustering.     

两种不同界面结合强度碳/铝复合材料的内耗特性

本文研究了两种不同界面结合强度的碳/铝复合材料经不同次数加载热循环处理后的内耗值及内耗机制。弱界面结合的C/L2复合材料的内耗值变化主要由界面脱粘引起,而强界面结合的C/LD2复合材料的内耗值变化主要由位错运动所致。     

The rank one mixed μ problem and ‘kharitonov-type’ analysis

The general mixed μ problem has been shown to be NP hard, so that the exact solution of the general problem is computationally intractable, except for small problems. In this paper we consider not the general problem, but a particular special case of this problem, the rank one mixed μ problem. We show that for this case the mixed μ problem is equivalent to its upper bound (which is convex), and it can in fact be computed easily (and exactly). This special case is shown to be equivalent to the so-called ‘affine parameter variation’ problem (for a polynomial with perturbed coefficients) which has been examined in detail in the literature, and for which several celebrated ‘Kharitonov-type’ results have been proven.