The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat
transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal
pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable
and the method is applicable to combustion and heat transfer of the marine supercharged boiler. 相似文献
People experience regulatory fit (E. T. Higgins, 2000) when the strategic manner of their goal pursuit suits their regulatory orientation, and this regulatory fit feels right. Fit violation feels wrong. Four studies tested the proposal that experiences of fit can transfer to moral evaluations. The authors examined transfer of feeling wrong from fit violation by having participants in a promotion or prevention focus recall transgressions of commission or omission (Studies 1 and 2). Both studies found that when the type of transgression was a fit violation, participants expressed more guilt. Studies 3 and 4 examined transfer of feeling right from regulatory fit. Participants evaluated conflict resolutions (Study 3) and public policies (Study 4) as more right when the means pursued had fit. (PsycINFO Database Record (c) 2010 APA, all rights reserved) 相似文献
The transit time of the coolant, and thus its velocity, has been measured using the temperature fluctuation at the outlet of a reactor core. An impulse response function estimation is introduced, which substitutes the widely used cross-correlation measurement technique. It is shown in theory and practice that the time delay estimation is improved when using the impulse response function instead of the cross-correlation function in parameter estimation. Extremely low velocities (down to 2 cm/sec) have been measured in a natural circulation regime in a research reactor. 相似文献
An ice slurry generation system was developed using direct contact heat transfer between water and the coolant, Fluroinert FC-84. The location of the coolant nozzle is an important design consideration to avoid clogging due to freezing of water. An ice fraction of up to about 40 percent was obtained with the nozzle located at the bottom of the ice slurry tank and the jet directed upwards into the water. Two simplified model were developed to extract the heat transfer coefficient between the coolant drops and the water. The first model requires as input the average drop diameter and the residence time while the second model uses the measured drop diameter distribution. The estimated heat transfer coefficients are much smaller than those computed using single-sphere correlations. 相似文献
Home storage is the final step of the frozen foods distribution chain, and little is known on how it affects the products quality. The present research describes frozen green beans (Phaseolus vulgaris, L.) quality retention profile during the recommended ‘star marking’ system dates, at the storage temperatures of +5, −6, −12 and −18 °C (along 1, 4, 14 and 60 days, respectively).
The quality profile was assessed by a simulation system. Simulations were set by a response surface methodology to access the effect of different packaging materials (thermal conductivities and thickness), surface heat transfer coefficient, and refrigerator dynamics (effect of refrigeration cycles at the different storage temperatures) on the average retentions of Ascorbic Acid, total vitamin C, colour and flavour.
Green beans quality losses along frozen storage are significantly influenced by temperature, refrigerator dynamics and kinetic properties. Quality is also highly dependent on packaging materials thermal insulation (e.g. at temperatures above the melting point). Temperature cycles inside frozen chambers have a long term effect, and at the higher storage temperatures (e.g. T>−6 °C) are detrimental to frozen green beans quality after shorter periods. 相似文献
Analysis on steady-state and transient heat transfer on a flat plate at the middle of a parallel duct immersed in He II was performed for bath temperatures from 1.8 to 2.1 K at 101.3 kPa. Two-dimensional computer code named SUPER-2D developed by the authors based on the two-fluid model and the theory of mutual friction was used. Steady-state critical heat flux (CHF) and the time lag from the application of a step heat input to λ transition, that is called a lifetime, were obtained numerically for various step heat fluxes and for the channel gaps from 2 to 20 mm. Effect of the gap restriction on the CHF and the lifetime were clarified. The solutions were compared with the experimental data for the ducts with the same structures and the corresponding conditions. They agreed well with the experimental data. The heat transport mechanism in the parallel duct was clarified. 相似文献
We discuss some different ideas about the sort of formalism appropriate for translation (more specifically, transfer) that have been explored within Eurotra. The intention is not to evaluate these different ideas, but to outline the issues of general interest and relevance that they raise. Section 1 describes some common assumptions, section 2 describes the different ways they have been interpreted, and section 3 considers some further implications. 相似文献