中频反应溅射SiO2膜与直流溅射ITO膜的在线联镀

多数ITO透明导电玻璃生产线在实现SiO2膜与ITO膜在线联镀时，应用SiO2靶射频溅射沉积SiO2膜工艺和ITO靶直流溅射沉积ITO膜工艺，如果SiO2膜应用硅靶反应磁控溅射工艺，存在这种工艺是否可以与ITO靶直流溅射沉积ITO膜工艺在线联用以及如何实现联用的问题。作者对现有的生产线进行了改造设计、加工，做了大量实验、质谱分析和多项测试研究，成功地实现反应溅射SiO2膜与ITO膜在线联镀，做到SiO2镀膜室的工作状态的变化基本上不影响ITO镀膜室的工艺条件。     

双辊薄带钢连铸在线自动检测系统

介绍了双辊薄带钢连铸工艺,设计了双辊连铸机的计算机在线自动检测系统,通过采取正确的抗干扰措施提高了检测的精度,系统在双辊薄带钢连铸试验中应用效果良好.     

连铸温度场数值模拟及冷却水参数优化

由于用实验方法来研究工艺参数对铸坯温度场的影响较困难,故而提出了一种在冶金冷却条件指导下的启发式GA(遗传算法)数值模拟优化方法,为优化工艺参数提供了理论依据,并在优化基础上采用MIMO(多输入多输出)系统PID(比例积分微分)控制器实现了二冷段配水的优化控制,改善了铸坯的质量.     

鞍钢1780mm热轧生产线"三电"工程施工概述

概述了鞍钢1780mm生产线技术改造工程中供电、传动及自动控制系统的构成、安装及调试技术要点,以及技术经济效果评述,可供同类工程施工参考.     

炼钢工序的变化与挑战——柳钢"十五"期间炼钢的进步与工艺特点

简述了炼钢工序在柳钢"十五"期间工艺和装备的变化及其特点.对工序变化进行了初步分析.     

A frame-based knowledge representation model and its mapping to nested relations

The first part of this paper introduces the basic constructs of a frame representation model and gives a formal definition for them. Subsequently the nested relational model (NF²) is described as an extension of the classical relational model to support relation-valued attributes. In the second part of this paper both models are compared with each other and a mapping of frame representation structures to NF² structures is specified. The structural similarities between frames and NF² relations are made clear and it is shown that their main difference is due to the type polymorphism introduced by the concept hierarchy of the frame model. This causes type collisions to occur in the strictly typed NF² model when frames are directly mapped to NF² structures. Two solutions to this problem are suggested and compared. The paper concludes with a reformulation of query operations of the frame model in terms of NF² algebra operations.     

Satellite SAR Remote Sensing of Great Lakes Ice Cover,Part 2. Ice Classification and Mapping

During the 1997 winter season, shipborne polarimetric backscatter measurements of Great Lakes (freshwater) ice types using the Jet Propulsion Laboratory C-band scatterometer, together with surface-based ice physical characterization measurements and environmental parameters, were acquired concurrently with Earth Resource Satellite 2 (ERS-2) and RADARSAT Synthetic Aperture Radar (SAR) data. This polarimetric data set, composed of over 20 variations of different ice types measured at incident angles from 0° to 60° for all polarizations, was processed to radar cross-section to establish a library of signatures (look-up table) for different ice types. The library is used in the computer classification of calibrated satellite SAR data. Computer analysis of ERS-2 and RADARSAT ScanSAR images of Great Lakes ice cover using a supervised classification technique indicates that different ice types in the ice cover can be identified and mapped, and that wind speed and direction can have an influence on the classification of water as ice based on single frequency, single polarization data. Once satellite SAR data are classified into ice types, the ice map provides important and necessary input for environmental protection and management, ice control and ice breaking operations, and ice forecasting and modeling efforts.     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Ensuring primary realization of pressure unit in the vacuum range without typically utilized static expansion system

After the break-up of Czechoslovakia in 1993 the primary metrological standards authority almost fully remained in Slovakia. So we had to build our primary vacuum metrology anew. But we could do it using uptodate techniques that are more effective and they enable us to fulfil our task more effectively and in a shorter time.The steady demand to widen the lower pressure range and a steady demand for maximal accuracy collide with the financial possibilities open to a small country. So it is impossible to follow the classical pattern for the vacuum standards: liquid columns, static expansion system and dynamic expansion system. But it is possible to utilize contemporary progress in construction of piston manometers. This enables us to discard liquid column and static expansion techniques in favour of piston technique [Tesar J, Prazak D. Vacuum 2002; 67: 311, Tesar J, Prazak D, Krajicek Z. In:Proceedings of international symposium on Pressure and Vacuum, 2003. p. 169, Tesar J, Repa P, Prazak D, Krajicek Z, Peksa L. Vacuum 2004; 76: 491.]. Such system fulfils all the needs of a little industrial country and is economically acceptable.     

碳酸化分解工艺的改进与实践

本文针对烧结法生产氧化铝过程中,铝酸钠溶液的碳酸化分解工艺,由间断分解到连续分解的改进进行了论述,指出连续分解是碳酸化分解的发展方向。