基体改性对C/C复合材料性能影响的研究(一)

本文从C/C复合材料的基体入手,研究了基体沥青、焦炭中添加氧化物的工艺条件及其在复合材料中的作用.结果表明,添加氧化物对基体改性,不仅能提高C/C复合材料的高温抗氧化性,也能对其它性能带来很大影响.只要控制适当的工艺条件,就可以得到高性能的C/C复合材料.     

The effect of fibre alignment on composite strength: II. The strength of angle-ply laminates

Experiments have been carried out on relatively wide angle-ply laminate samples with very short gauge lengths. These proved to be very much stronger than samples tested in earlier work, and which form the basis for our present design with these materials. It is highly likely that the early results for strength were more indicative of edge effects than true laminate strength. This is confirmed by data from tests on pressurized tubes. A review of the literature on this shows that such tests produced results which can be an order of magnitude higher than the early laminate tests. Thus our design calculations could well be severely underestimating the potential strength of angle-ply laminates. This may be having serious consequences for the aerospace industry, through the use of design criteria for strength which may be too conservative. Single-fibre experiments may pave the way for more realistic estimates of angle-ply laminate strengths. These indicate that a simple one-third power rule can be used to estimate the potential strength. However, this is purely ad hoc at present, and needs to be put on a firmer footing through both theoretical and experimental studies. Furthermore, if this approach is adopted, edge effects will still have to be allowed for, and estimated on the basis of the aspect ratio of the part.     

Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

Colour extension properties of individual pigments and effects on shades of foundations in cake form

The mechanism of colour change during the pigment dispersion process and during powder application to the skin surface was studied by examining the colour extension properties of Yellow. Red , and Black iron oxides in white powder bases. A new measure for the evaluation of the degree of colour extension was devised. This measure corresponded well with human visual sensation, and was found to be useful for comparing the rates of colour extension of pigments. The rate of colour extension of pigments was found to vary in the order: Yellow acicular Red granular Red Black. This result explains colour darkening and the change towards reddish tones during the pigment dispersion process, because Yellow extends fully in the early stage of the process but Red , especially in granular form, and Black continue to extend even in the later stage. Acicular Red iron oxide is more favourably employed than the granular form to attain sufficient colour extension of foundations with lower energy expenditure, and to decrease the discrepancy between the cake colour and the colour of applied powder.
Le développement des oxydes de fer et effet sur les nuances des fonds de teint compacts     

多层住宅砖混房屋设计中两点问题的探讨

浅议多层住宅砖混房屋中构造柱的作用及设置方法；探讨了砖混结构墙下条形基础底面积重复利用问题及其解决方法。     

SiC粒子增强铸造Al基复合材料的研制

本文用真空烘烤封罐法对 SiC 粒子进行预处理,在固液两相区内搅拌添加,制造了铸造 Al 基复合材料。测试表明,该复合材料具有铸造性能好,力学性能高的优点,适用于采用压铸、石膏型精密铸造、金属型铸造等工艺方法成型的活塞、连杆等要求苛刻的零件。     

分离有机/有机混合物的PVA、CA系列膜及其渗透汽化性能研究(Ⅱ) 成膜条件对渗透汽化性能的影响

用溶剂完全蒸发法制备了PVA复合膜 .经对MTBE/MeOH混合物的分离实验得到了PVA复合膜的最佳成膜条件 ,即 :铸膜液中PVA、马来酸浓度分别为 7%、3% ,热处理温度130～ 15 0℃ .在 1%～ 2 %丙酮水溶液中浸泡处理 4～ 8h ,CTA中空纤维RO膜被改性成渗透汽化膜 .CTA中空纤维膜的分离性能优于其它醋酸纤维素系列膜 ,PVA/CA复合膜的性能优于PVA/PAN复合膜和CA/PAN复合膜     

Effect of the particle size ratio on the conductivity of conductor-insulator powder composites: Numerical simulation

A theoretical method for determining the percolation limit and effective conductivity of composites based on polydisperse mixtures of insulator and conductor powders is proposed. The effect of the particle size ratio between the insulator and conductor on the percolation limit and effective conductivity is studied. Numerical simulation of the microstructure, effective properties, and percolation limit in composites is discussed. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 31–40, 2007.     

Exact solution of elasto-plastic stresses in a metal-matrix composite beam of arbitrary orientation subjected to transverse loads

An analytical elasto-plastic stress analysis is presented for a metal-matrix composite beam of arbitrary orientation subjected to a single transverse force applied to the free end of the beam and a uniformly distributed load. The material is assumed to be perfectly plastic in the elasto-plastic solution. A composite consisting of stainless-steel-reinforced aluminum was produced for this work. Sample problems are given for various orientation angles. Elastic, elastoplastic and residual normal and shear stresses are calculated. The location of the elasto-plastic boundary of the beam is obtained according to the x coordinates of the beam.     

光纤智能复合材料

对光纤型智能复合材料的工作原理，性能特点和应用前景作了介绍，并讨论了制造成型的技术问题。