预应力钢-混凝土组合梁的应用与研究

回顾了预应力钢 混凝土组合梁国内外应用与研究历史 ,分析了现有规范及理论的不足 ,并指出了有待解决的问题。     

空心微珠改性硬质聚氯乙烯复合材料的应用研究

经过改性的超细空心微珠可以作为填料加入到硬质聚氯乙烯（PVC－U）树脂中，同时改善PVC树脂的流变性、冲击性能和刚性等性能。研究结果表明，超细空心微珠加入到硬质PVC管材中，可以明显改善PVC硬管的加工流动性能，显著缩短塑化时间，降低最大扭矩。而超细空民微珠加入到硬质PVC板材时，可以提高PVC硬板的冲击性能，减小制品的收缩率，赋予PVC硬板优异的耐腐蚀性能，且产品的各项性能均符合PVC板材国家标准GB／T4454－96。     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

金属－橡胶硫化粘接过程中分子取向行为的间接证据

对金属－橡胶热硫化粘接复合体的剥离行为进行了研究，同一粘接试样的双向１８０°剥离试验显示出了巨大的差异。本文分析了弹性材料在硫化过程中的分子行为，并提出了相应的新假设，认为这是由于金属－橡胶在硫化粘接过程中分子取向交联行为所致。这种双向１８０°剥离破坏现象可被看作是金属－橡胶硫化粘接过程中分子取向行为的间接证据。     

T_C≥400°C高温PTC陶瓷的研制

利用国产原料，采用传统的陶瓷材料制备工艺，研制了居里温度ＴＣ≥４００°Ｃ的高温ＰＴＣ陶瓷，制成了居里温度ＴＣ＝４１２°Ｃ，电阻Ｒ≤１０３Ω，ｌｇ（Ｒｍａｘ／Ｒｍｉｎ）＝４的高性能ＰＴＣ热敏陶瓷材料     

聚吡咯导电材料合成方法的进展

本文对聚吡咯及聚吡咯导电复合物的合成方法进行了综述。     

SO3和C3A对水泥膨胀性能的影响

本文研究了ＳＯ３和Ｃ３Ａ对水泥浆体膨胀的影响。对于某一较早的龄期，当ＳＯ３掺量超过某一数值时，水泥浆体的膨胀与ＳＯ３掺量关系不大，而提高水泥的Ｃ３Ａ含量则能显著地增加其膨胀。本文还探讨了ＳＯ３和Ｃ３Ａ影响水泥浆体膨胀的机理。     

化学镀SiCp／Ni－P复合镀层与基体结合强度及其影响因素

论述了ＳｉＣｐ／Ｎｉ－Ｐ复合镀层与钢基体的结合强度及其影响因素。复合镀层中离界面５μｍ厚度以内区域的组成及应力状态对镀层／基体的界面结合有决定性作用，在该区域以外ＳｉＣ粒径变化不影响镀层的结合强度。适当的热处理可提高界面结合力。     

Analysis of adhesive bonded composite lap joints with transverse stitching

The effect of transverse stitching on the stresses in the adhesive is investigated using an adhesive sandwich model with nonlinear adhesive properties and a transverse stitching model for adhesive bonded composite single-lap and double-lap joints. Numerical results indicate that, among all stitching parameters, thread pretension and stitch density have significant effect on the peel stresses in the adhesive; increase in the thread pretension and the stitch density leads to a decrease in peel stress in the adhesive, while an increase in other parameters generally results in a negligible reduction in peel stress. The effect of stitching was found to be negligible on the shear stresses in the adhesive. Thus it is concluded that stitching is effective for the joints where peel stresses are critical and ineffective for those where shear stresses are critical.     

ANALYSIS ON ROOM TEMPERATURE TENSILE STRENGTH OF δ-Al_2O_3, FIBER / Al-12Si COMPOSITE

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度δｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τＰ确定复合材料的ＲＯＭ预测曲线，应首先判断σｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论。