反应器和钢烟囱整体吊装的难点和对策

介绍了在金陵石化炼油厂200万t/a柴油加氢装置建设中,将质量为237t的反应器和高60m的钢烟囱成功进行整体吊装过程中的关键技术.通过此项工程实践得出以下结论象钢烟囱这样细长重物的整体吊装,由两台吊车抬立起后,再由主吊车独立吊装就位的施工方法简单易行,安全可靠,应用范围广;结构复杂细长杆的吊装强度和挠度计算比较复杂,在计算过程中可以忽略部分次要件的质量,分别以两吊点为支点计算上下吊点所受的力,然后再按比例放余量,使两吊点受力之和等于细长杆的重力,计算挠度时,可以适当地把问题夸大化,从而建立近似的力学模型;高压厚壁重型容器的吊装,宜直接设置专门吊盖与大法兰用螺栓把紧起吊;施工现场地基坚实是保证吊车站位和吊装施工的前提条件.     

Neural network systems to reproduce crash behavior of structural components

The use of neural networks as global approximation tool in crashworthiness problems is here investigated. Neural networks are not only asked to return some meaningful indices of the structural behavior but also to reproduce load-time curves during crash phenomena. To contain the number of examples required for the training process, parallel subsystems of small neural networks are designed. Design points for the training process are obtained by explicit finite element analyses performed by PAMCRASH. The settlement of the points in the design domain is defined using a maximum distance concept. The procedure is applied to different typical absorption structures made of aluminum alloy: riveted tubes, honeycomb structures, longitudinal keel beam and intersection elements of helicopter subfloors.     

合金钢连铸机生产工艺分析及实践

对新钢特殊钢有限责任公司整个合金钢连铸机的生产工艺进行了分析，提出了提高钢水质量和优化连铸工艺参数的有效措施，使铸坯的质量得到了有效控制和改善。     

In‐Situ Observation of the Formation of MnS during Solidification of High Sulphur Steels

A Confocal Scanning Laser Microscope equipped with a gold image furnace was used to directly observe the precipitation of MnS during solidification of high sulphur steels under isothermal conditions in the temperature region 1440 to 1480°C on the free surface of the steel melt. For the case of Al‐killed steels, below 1480°C MnS particles were found to precipitate with Fe forming simultaneously around them. This MnS containing structure continued to grow rapidly (264 μm/s) as a surface film. The film gradually changed, as the level of S in the melt decreased, into a eutectic structure (with lamella spacing of 2 μm) as predicted by thermodynamics. In Si‐ killed steels there was significantly lower tendency to form MnS both in terms of time until precipitation occurred and growth rate.     

热镀锌工艺对Ti-IF钢光整热镀锌板组织和性能的影响

在连续热镀锌线上研究了RTH带钢温度和光整延伸率对Ti—IF钢光整热镀锌板组织和性能的影响。试验表明，当RTH带钢温度在830℃以下时，成品铁素体晶粒度为10．0级，织构类型以{332}、{114}为主，随着带钢温度的进一步提高，热镀锌板的晶粒逐渐粗化，织构成为典型的{111}织构，且取向密度增加，r值随之提高，但当带钢温度在900℃以上时，织构又趋于无规则分布，r值显著降低；光整延伸率对Ti—IF钢光整热镀锌板力学性能的影响很大，随着光整延伸率的提高，屈服强度明显提高，n值明显降低，延伸率降低，抗拉强度变化较小，且光整延伸率对性能的影响与成品铁素体晶粒尺寸有关，成品晶粒越粗，光整延伸率的影响越大。因此对于Ti—IF钢光整热镀锌板而言，n、r值是一对矛盾体，在制订热镀锌工艺时，需根据使用条件的不同，对其n、r值进行综合考虑。     

稀土改善09CuPTiRE耐候钢耐蚀性的作用机理

应用扫描电镜(SEM)、离子探针(IMA)、X射线光电子能谱(XPS)和交流阻抗法研究含不同稀土耐候钢稀土提高耐大气腐蚀作用机理。结果表明,合适的稀土含量可显著提高钢的耐腐蚀性,稀土能促进Si、Cu和P在内锈层中以Si~(4+)、Cu~+和P~(5+)形态富集,并观察到锈层中的稀土。钢中加入稀土形成了致密连续厚而粘附性好的含硅铜稀土的复合铁锈层,从而提高了抗大气腐蚀性能。     

New rotary valves for pulse-tube refrigerators

In most used rotary valves in GM-type pulse-tube refrigerators the rotor makes heavy mechanical contact with the stator, so the valve is liable to wear, and large torques are needed. In this paper we will describe two types of valves, which have balanced forces on the rotor. In the first valve the rotor and the stator make no mechanical contact. The second type is a contact valve, like the classical valves, but the forces on the rotor are balanced in a different way. Therefore, these valves are less liable to wear, and the torques needed to rotate the valves are small.     

SLIMLINE+K型多功能撬装双滚筒试井绞车简介

SLIMLINE K型多功能撬装双滚筒试井绞车为整体式结构，多用于海上平台，可进行电子压力计和机械压力计试井，以及井下工具的投放、震击、打捞等完井作业。该试井绞车采用先进的数控技术，使起下纲丝／电缆实现自动化控制，该系统能够对斜井、定向井进行随钻测试。     

珠钢不锈钢冶炼技术探讨

本文阐述了不锈钢冶炼的关键技术，为生产准备提供帮助。     

乳化型轧制液的质量标准研究

对国内目前所使用的冷轧薄钢板(汽车钢板)轧制液母液和乳化液的质量指标及常用试验评定方法进行了考察，并对产品的性能要求进行了研究与分析，制订出一套标准以供参考，包括乳化液稳定性、润滑性、防锈性、抗泡性、使用周期及粘度、闪点等性能。