不同分散剂对细粒高硫煤及煤系黄铁矿的选择性分散

主要研究六偏磷酸钠和腐植酸纳２种分散剂分别对细粒高硫煤、煤系黄铁矿悬浮液的分散作用，考察了分散剂用量、介质ｐＨ值对细粒煤与煤系黄铁矿选择性分散的影响。     

Desulfurization of commercial fuels by π-complexation: Monolayer CuCl/γ-Al2O3

Monolayer CuCl/γ-Al₂O₃ sorbent was studied for desulfurization of a commercial jet fuel (364.3 ppmw S) and a commercial diesel (140 ppmw S). The sorbent was prepared by means of spontaneous monolayer dispersion methods. Deep desulfurization (sulfur levels of <1 ppmw) was accomplished with this sorbent using a fixed-bed adsorber. The CuCl/γ-Al₂O₃ sorbent was capable of removing 6.4 and 11.2 mg of sulfur per gram for jet fuel at breakthrough (at <1 ppmw S) and saturation, respectively. The same sorbent was capable of removing 0.94 and 1.8 mg of sulfur per gram for BP diesel at breakthrough and saturation, respectively. The difference in sulfur capacities for jet fuel and diesel was apparently caused by the difference in concentrations of strongly binding compounds, such as nitrogen heterocycles, heavy (polynuclear) aromatics and fuel additives. In comparison with CuCl/γ-Al₂O₃, Cu(I)Y zeolite has higher sulfur capacities but is less stable and can be easily oxidized to Cu(II)Y by fuel additives (such as oxygenates) and moisture and consequently loses π-complexation ability. However, all these cuprous π-complexation sorbents selectively adsorb thiophenic compounds over aromatics and olefins (as predicted by the high separation factors), which resulted in the observed desulfurization capability. A feasibility study is shown for efficient regeneration of CuCl/γ-Al₂O₃ using ultrasound at ambient temperature. Possible problems associated with desulfurization using π-complexation sorbents for commercial fuels are discussed.     

远红外日用陶瓷釉的研究

通过在普通日用陶瓷釉中掺入远红外陶瓷粉,研究了远红外陶瓷粉对釉面质量(白度、光泽度、显微硬度)及远红外陶瓷釉辐射率的影响,探讨了不同分散剂对远红外陶瓷粉在基釉中的分散情况及其对陶瓷釉显微结构的影响。制备出了符合国家日用瓷质量标准、且具有高的远红外辐射性能的远红外日用陶瓷釉。     

A new Probe Guided Mutation operator and its application for solving the cardinality constrained portfolio optimization problem

This paper revisits the classical Polynomial Mutation (PLM) operator and proposes a new probe guided version of the PLM operator designed to be used in conjunction with Multiobjective Evolutionary Algorithms (MOEAs). The proposed Probe Guided Mutation (PGM) operator is validated by using data sets from six different stock markets. The performance of the proposed PGM operator is assessed in comparison with the one of the classical PLM with the assistance of the Non-dominated Sorting Genetic Algorithm II (NSGAII) and the Strength Pareto Evolutionary Algorithm 2 (SPEA2). The evaluation of the performance is based on three performance metrics, namely Hypervolume, Spread and Epsilon indicator. The experimental results reveal that the proposed PGM operator outperforms with confidence the performance of the classical PLM operator for all performance metrics when applied to the solution of the cardinality constrained portfolio optimization problem (CCPOP). We also calculate the True Efficient Frontier (TEF) of the CCPOP by formulating the CCPOP as a Mixed Integer Quadratic Program (MIQP) and we compare the relevant results with the approximate efficient frontiers that are generated by the proposed PGM operator. The results confirm that the PGM operator generates near optimal solutions that lie very close or in certain cases overlap with the TEF.     

聚偏氟乙烯/聚丙烯酸酯复合乳液的合成与性能

在含氟表面活性剂存在下，将聚偏氟乙烯超声分散于甲基丙烯酸甲酯和丙烯酸丁酯的混合单体中进行乳液聚合，制备了聚偏氟乙烯／聚丙烯酸酯复合乳液。采用动态光散射DLS、透射电镜TEM和红外光谱FT—IR对乳液组成及乳胶粒子的形态进行了表征，并对聚合物胶膜的性能进行了测试分析。结果表明：聚偏氟乙烯的加入，使复合乳液膜的拉伸强度显著增大，吸水率减小。     

In situ visualization of drop deformation,erosion, and breakup in high viscosity ratio polymeric systems under high shearing stress conditions

In this paper, deformation and breakup under simple shear of single molten polymer drops in a polymer matrix were investigated. Flow visualization was carried out in a Couette‐Flow apparatus under relatively high shear rates and temperatures up to 230°C. Drop/Matrix combinations were composed of polystyrene drops of 0.5–0.6 mm in diameter in polyethylene matrix, and ethylene–propylene copolymer drops of approximately the same size in polypropylene matrix. The deformation and breakup processes were studied under steady state and time‐dependent shearing conditions. Either for steady state or time‐dependant shearing conditions, drop elasticity generated at relatively high shear rates helped the drops to align perpendicular to the flow direction, i.e., parallel to vorticity axis. Also, the most striking non‐Newtonian effects for the high viscosity ratio systems were the surface erosion and the drop splitting mechanisms. The particles eroded off the main droplet surface were very fine, in the range of 10–50 μm, and led to a significant reduction in main drop size before its final breakup. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2582–2591, 2006     

Optimising the dewatering behaviour of clay tailings through interfacial chemistry, orthokinetic flocculation and controlled shear

The effect of shear on dewatering behaviour and particle interactions of Na-exchanged smectite and kaolinite clay dispersions has been investigated at pH 7.5, using hydrolysable Ca(II) and Mn(II) ions as coagulants and high molecular weight anionic and non-ionic polyacrylamide (PAM A and PAM N, respectively) and polyethylene oxide (PEO) flocculants. Metal ion addition enhanced the flocculation performance by dramatically reducing the magnitude of the particle zeta potential and, in the case of smectite pulp, suppressing osmotic swelling. Under optimum orthokinetic flocculation conditions of controlled agitation rate and duration, PAM A and PEO-based flocs settled faster than those of PAM N whilst kaolinite pulps produced higher sedimentation rates than smectite pulps. The settling rates are nearly an order of magnitude greater than those observed under standard flocculant-pulp mixing/flocculation methods of inversion and plunging. The difference in the flocculant behaviour is attributed to the more expanded conformation of PAM A and PEO polymer chains in contrast to PAM N, whilst the lower yield stresses, reflecting inter-particle bridging and floc network structure strength that are conducive to faster clarification, were displayed by kaolinite pulps. Following shear, similar consolidation enhancement of ≈ 5-7 wt.% solid for both pulps was achieved at an optimum agitation range of 100-200 rpm. This was accompanied by decreased yield stress in the case of PAM A-based pulps, indicating non-reversible disruption of polymer mediated particle and floc network structure. In contrast, the yield stresses of PAM N and PEO flocculated dispersions indicated similar and stronger particle interactions, respectively, upon consolidation following shear. The findings show clear links between effect of shear, interfacial chemistry and polymer structure on pulp particle interactions and dewaterability.     

Effects of ion group content and polyol molecular weight on physical properties of HTPB‐based waterborne poly(urethane‐urea)s

A series of waterborne poly(urethane‐urea)s, WPUUs, based on using nonpolar hydroxyl‐terminated polybutadiene (HTPB) as the soft segment, were successfully synthesized in this article. The effects of the COOH group content and soft‐segment molecular weight (Mn_s) on the dispersion, morphology, and physical properties were investigated. Variations of the particle size, viscosity, and zeta potential were first governed by the hydrophilicity of the polymer chain, and then by the swelling derived from water. Fourier transfer infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) indicated that the degree of phase separation decreased as the COOH group content increased or as Mn_s decreased. However, the hydrogen bonding between the soft and hard segments and the two‐phase mixing could not occur in this nonpolar HTPB‐based WPUU system, indicating that the hard segments tended to form smaller domains and to pack more loosely. It was attributed to the fact that the presence of bulky ionic salt groups destroyed the ordered arrangement of the hard segments. In this case, the increases of the interface area between the soft and hard phases resulted in that the present behaviors were similar to the phase mixing. In tensile properties, HTPB‐based WPUUs exhibited higher tensile stress, elongation at break, and modulus as the COOH group content decreased or as Mn_s decreased. In thermal degradation, the introduction of HTPB polyol improved the thermal stability of WPUU. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Gas Hold‐Up in Stirred Tank Reactors in the Presence of Inorganic Electrolytes

Gas hold‐up (?_G) in air‐aqueous electrolyte solutions in stirred tank reactors (STR) is correlated using a relative gas dispersion parameter, N/N_cd and a surface tension factor (STF), (c/z)(dδ/dc)². For electrolyte concentration below transition concentration (c_t) a single correlation in the form of ?_G = f(N/N_cd, vvm, STF) shows good agreement with gas hold‐up data over a wide range of system and operating conditions. Above ct no effect of STF on gas hold‐up is observed and the correlation obtained is of the form ?_G = f(N/N_cd, vvm). Data available in the literature on large STR show good fit with the proposed correlation.     

Ultrasonic Dispersion of Ceramic Powders

Ultrasonication is very effective in dispersing alumina and barium titanate slurries. When optimum conditions are used, very short durations (2 to 3 min) are enough to achieve well-dispersed, stable suspensions.