连续梁的简便计算

利用三转角方程，对连续梁的内力进行精确的计算，该方法简捷明了，便于应用。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

分析型全蒸发器在啤酒挥发性成分测定中的应用

综述了分型全蒸发器技术在啤酒发酵过程中的应用状况，并介绍了分析型全蒸发器模型结构及与之配合使用的连续多分支管。     

新世纪我国压铸业与国际接轨的思考

针对中国压铸行业的现状和存在的问题 ,以及当前的机遇和面临的挑战 ,论述了中国压铸工业进入 2 1世纪所面临的新形势及应采取的对策     

露天矿半连续工艺技术应用现状及发展前景

介绍了露天矿半连续工艺技术国内外应用现状、研究成果以及发展趋势。     

Continuous precipitation of calcium sulfate dihydrate from waste sulfuric acid and lime

Precipitation of calcium sulfate dihydrate, gypsum, from (i) a pure sulfuric acid/lime suspension and (ii) a waste sulfuric acid/lime suspension in a continuous pilot plant in the temperature range from 40 °C to 80 °C was studied. It was observed that in the case of waste sulfuric acid with a high content of Mg²⁺ and Fe²⁺ ions, several hours after the beginning of the precipitation, partial dissolution of the product and modification of the crystals from needle‐ and plate‐like to agglomerated structures occurred. It is suggested that the secondary changes occur due to the increased concentration of Mg²⁺ and Fe²⁺ ions in the reactor. Below 60 °C, and above 70 °C plate‐like and needle‐like single crystals respectively were formed. The mean size (d₅₀) of the crystals was found to increase with increasing temperature and decrease with the initial concentration of lime. Gypsum produced between 70 °C and 80 °C is suitable for further processing for construction plaster. In a precipitation process with pure sulfuric acid only single perfect needle‐like crystals occurred. Copyright © 2005 Society of Chemical Industry     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

碳纤维复合材料柔性连续抽油杆开发及应用

碳纤维柔性连续抽油杆选用高性能碳纤维 ,以环氧树脂胶液为基体材料 ,添加一定配比的固化剂、促进剂和脱模剂 ,采用拉挤成型工艺制成 ,其开发的关键技术是连续成型、连接接头和安全保险装置。现场应用试验表明 ,TXC— 1、TXC— 2、TXC— 3三种规格的碳纤维柔性连续抽油杆能可靠应用于泵挂深度分别为 12 0 0、 180 0、 30 0 0m的直井和斜井中 ,实测比钢抽油杆节电 ,日产油量提高 。节能增产效果显著。     

薄板坯连铸生产SS400钢工艺技术研究

对唐钢薄板坯连铸机生产的SS400钢的生产工艺进行了分析,认为薄板坯连铸机生产的SS400钢,在采取了精炼站在线定氧,将钢水全氧控制在25×10~(-6)左右,同时连铸采取保护浇注和轻压下等技术后,能够确保薄板坯连铸SS400钢的顺利浇注,轧制的板带材表面质量良好,机械性能符合要求。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。