连铸温度场数值模拟及冷却水参数优化

由于用实验方法来研究工艺参数对铸坯温度场的影响较困难,故而提出了一种在冶金冷却条件指导下的启发式GA(遗传算法)数值模拟优化方法,为优化工艺参数提供了理论依据,并在优化基础上采用MIMO(多输入多输出)系统PID(比例积分微分)控制器实现了二冷段配水的优化控制,改善了铸坯的质量.     

铜冶炼企业金银回收率计算方法的选择

针对某厂金、银总平衡情况，分别采用平衡法和连乘法计算金、银回收率，得出两种不同的结果，文章分析了产生不同结果的原因，探讨不同的企业如何根据自身特点，选择与之相适应的金、银回收率计算方法，以便准确地反映本企业的回收率实际水平。     

鞍钢1780mm热轧生产线"三电"工程施工概述

概述了鞍钢1780mm生产线技术改造工程中供电、传动及自动控制系统的构成、安装及调试技术要点,以及技术经济效果评述,可供同类工程施工参考.     

桥梁颤振气动导数识别的迭代法

本文提出一种利用自由振动响应通过年顿－拉夫逊迭代同时识别出桥梁全部8个颤振气动导的方法。此法具有对迭代初值要求不高，识别结果稳定的特点，并具有一定的抗噪声干扰能力。数字仿真与实物试验结果表明本文方法有效，可行。     

炼钢工序的变化与挑战——柳钢"十五"期间炼钢的进步与工艺特点

简述了炼钢工序在柳钢"十五"期间工艺和装备的变化及其特点.对工序变化进行了初步分析.     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

CSP连铸机大型液压缸的故障分析与改进

论述引进德国SMS连铸机大包托臂液压缸存在的寿命短问题，分析设计制造缺陷．通过增大缸头密封支持面、(φ600)内圆孔倒角、再增加一道软支撑环、缸头导向部分开润滑槽、改进球杆的润滑流道、柱塞杆整体淬火等措施，消除了原来的问题．同时分析了此项改进的技术经济效果．     

An investigation of the relation between the temperature dependences of the initial unbalance and the output signal of resistance strain sensor bridge circuits

The relation between the initial unbalance and the output signal of bridge circuits when acted upon simultaneously by the physical factor being measured and the temperature of the surroundings when the bridge is supplied from a voltage or current source is investigated. Analytic relations are obtained which explain the temperature dependence of the useful output voltage under external physical action. __________ Translated from Izmeritel’naya Tekhnika, No. 1, pp. 48–49, 2007.     

地下连续墙在太钢老厂改造工程中的应用

结合某深基坑支护施工实例 ,介绍了采用多头潜水钻成槽机进行地下连续墙施工的基本原理、工艺流程及注意事项。指出该方案对于在老厂区改造工程狭窄场地条件下 ,解决深基坑施工保护附近建 (构 )筑物安全具有独特的优势     

Ensuring primary realization of pressure unit in the vacuum range without typically utilized static expansion system

After the break-up of Czechoslovakia in 1993 the primary metrological standards authority almost fully remained in Slovakia. So we had to build our primary vacuum metrology anew. But we could do it using uptodate techniques that are more effective and they enable us to fulfil our task more effectively and in a shorter time.The steady demand to widen the lower pressure range and a steady demand for maximal accuracy collide with the financial possibilities open to a small country. So it is impossible to follow the classical pattern for the vacuum standards: liquid columns, static expansion system and dynamic expansion system. But it is possible to utilize contemporary progress in construction of piston manometers. This enables us to discard liquid column and static expansion techniques in favour of piston technique [Tesar J, Prazak D. Vacuum 2002; 67: 311, Tesar J, Prazak D, Krajicek Z. In:Proceedings of international symposium on Pressure and Vacuum, 2003. p. 169, Tesar J, Repa P, Prazak D, Krajicek Z, Peksa L. Vacuum 2004; 76: 491.]. Such system fulfils all the needs of a little industrial country and is economically acceptable.