管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

多孔挡板流化床还原UO3反应器模型的研究

针对ＵＯ＿３的Ｎ＿２还原反应建立了多孔挡板流化床反应器模型。将多孔挡板床的每一级视为具有相似的流动状态，每一级的上、下段称为稀、密相段，分别用鼓泡床和活塞流模型描述。该模型的计算值与￠６３ｍｍ的多孔挡板床Ｈ＿２还原ＵＯ＿３的热态实验值能较好的吻合。还预计了还原温度、操作气速和挡板结构参数对固相转化率的影响，为该类反应器的工业设计、放大和优化提供了依据。     

压水堆硼稀释事故的计算

一、概述核电厂压水堆的初始过剩反应性是通过控制捧、固体可燃毒物和溶解在主回路冷却剂中的硼酸等三种方式联合控制的。随着反应堆的燃耗和裂变毒物的积累,堆的过剩反应性不断减少,需要通过化容系统,控制硼酸的浓度来进行补偿。如果化容系统发生故障或操作员误操作,就会给回路注入无硼或低于规定浓度的补给水,给反应堆引入正反应性,造成硼稀释事故。按核安全法规的要求,应对换料、冷停堆、热停堆和启动等工况进行计算,并要求在这些     

Transient operation of a catalytic liquid-liquid plug flow reactor for kinetics measurements

A centrifugal partition chromatograph (CPC) was used as a liquid-liquid catalytic reactor for the isomerisation of hexen-3-ol into ethylpropylketone with a water soluble rhodium catalyst. Global mass transfer coefficients were measured and shown to depend on both the nature of the solute and the flow rate. Liquid-liquid partition isotherms were also determined with the CPC using elution chromatography. Finally, a reactor model was derived to account for the experimental results obtained both under stationary and transient (pulse) conditions. A parameter sensitivity evaluation is also presented.     

大型储罐的罐壁设计

根据十万立方米浮顶油罐罐壁板应力测试的实测结果，运用应力分析程序，对罐壁板应力分布情况进行了分析和比较，通过调整罐壁板的厚度，使新设计储罐的罐壁板应力分布更加均匀、合理。     

WTG420铁路罐车用钢的组织结构和力学性能分析

分析了ＷＴＧ４２０铁路罐车用钢的组织结构和力学性能。提出了冶炼与轧制的技术关键，其一，添加稀土元素改善钢中夹杂物；其二，采用控轧控冷使铁素体晶粒细化。     

小方坯连铸机的PLC自动控制

本文对弧型小方坯连铸机工艺与设备进行了分析，介绍了连铸生产的ＰＬＣ控制系统。及其软件设计。     

Onset of gas self-induction and power consumption after gas induction in an agitated tank

The behavior of inducted gas from liquid surface and the; power requirements in an agitated tank using a mechanical agitator are studied in order to increase the amount of gas self-induction and the gas retention time for gas absorption. A 45° six-blade downward impeller turbine was utilized in this study. Air and water, air and 40 wt% 60 wt%, and 80 wt% of glycerin water, and air and 106 cP silicon oil were employed as gas and liquid phases. Variables which were studied included geometrical factors (immersed depth of impeller, baffle with and diameter of impeller) and the physical properties of the liquid (viscosity, density, and surface tension). The correlations for the onset speed of impeller and power consumption after gas induction in the agitated tank are established from our experimental results. The amount of gas self-induction from the liquid surface in the agitated tank increases with increasing impeller diameter and speed and decreases with increasing baffle width, depth of impeller and viscosity of liquid.     

铅黄铜水平连铸棒材熔铸工艺的试验研究

在工业生产条件下，对影响HPb59－1水平连铸律材热轧开裂的熔铸工艺进行了试验研究．取三个熔铸工艺因素：铸造速度、冷却水压力、冷却水温度．试验结果表明；铸造速度对热轧开裂影响极为显著，使其控制在410mm／min左右可获得较为理想的效果．