双轴加载条件下疲劳裂纹扩展的研究

在双轴加载条件下对Ⅰ型疲劳裂纹扩展进行了研究。载荷范围从0.08σ_s到0.71σ_3,包括比例加载和非比例加载。基于对Von Mises理论的讨论,提出一个新的力学参数。双轴加载条件下的弹塑性参数P成功地描述了双轴比例加载和非比例加载下的疲劳裂纹扩展。     

水工混凝土构件裂缝检测方法及应用

水利工程在长期运行过程中,其混凝土构件会出现磨蚀、裂缝等损伤,如这类问题不能够及时得到处理,将会严重影响水利工程的安全运行。本次研究主要针对水工混凝土构件中的裂缝检测方法进行研究,提出从“定性”到“定量”的一体化检测思路,具体实施过程分为四部分,即“普探—详查—判定—验证”,其中,普探阶段采用探地雷达法,确定裂缝的总体分布;详查阶段采用超声横波反射三维成像的方法,确定裂缝的纵深向分布;判定阶段分别采用裂缝测宽法和表面声波法,用来确定裂缝的表面宽度和贯穿深度;验证采用钻孔电视,确定探测结果的正确性和准确性。上述技术路线突破了单一方法的限制,可有效地运用于水工混凝土构件裂缝检测,经实践证实,具有良好的检测效果。     

CYCLIC DEFORMATION OF COARSE GRAINED POLYCRYSTALLINE PURE Al——Ⅱ.FRACTURE SURFACE MORPHOLOGY

SEM photos for very coarse grained and high ductile polycrystalline pure Al show followingcharacteristics:A few fracture sources are concentrated,the crack propagates in fan-shapenear them,and the fatigue striations are cyclic cleavage facets.Each striation consists of awide cleavage facet and a narrow cleavage stage.Those stages often blunt due to plasticdeformation.The fatigue striations are clear and continual,and distribute over whole zone ofstage Ⅱ crack propagation.Two kinds of fatigue striations form in different levels,areconjoined by a“twisted baked piece of pastry”band.The secondary crack along the fatiguestriations was observed frequently.Some of them have already developed into secondarymacrocracks and secondary fatigue striations were found clearly on secondary fracture sur-face.The fracture surface can be divided into two parts,initiation and propagation zone of thecrack,however,no statical-fracture zone was observed.The mechanism to form striationswas preliminarily discussed.     

AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

疲劳裂纹扩展行为的研究现状及钛合金的疲劳裂纹扩展特征

疲劳裂纹扩展行为是现代材料研究中重要的内容之一。论述了组织结构、环境温度、腐蚀条件以及载荷应力比、频率变化对材料疲劳裂纹扩展行为的影响。总结出疲劳裂纹扩展研究的常用方法和理论模型,并讨论了"塑性钝化模型"和"裂纹闭合效应"与实际观察结果存在的矛盾。最后,对钛合金疲劳裂纹扩展研究的内容和研究结果进行了概述。     

WD615曲轴箱清理磨削裂纹的机理初探

WD615曲轴箱在机加工过程中，经常发现在铸件的上下平面出现细小的裂纹，其中一部分主要是在曲轴箱毛坯铸造过程中采用磨床磨削清理时产生的磨削裂纹。作者提出了铸件毛坯磨削裂纹的定义，并引用机加工磨削加工中的磨削烧伤理论进行了分析。     

火炮底板开裂分析

某公司购买的热轧钢板用于制作火炮底板,经数控火焰切割后,在过渡圆弧角处出现裂纹。采用化学成分分析、力学性能检测、金相检验、扫描电镜观察等方法对裂纹形成原因进行分析。结果表明:底板的化学成分和主要力学性能指标正常,原始组织粗大降低了材料性能。底板经火焰切割后组织变化较大,产生了粗大贝氏体和马氏体等不良组织,综合分析认为,底板断裂的主要原因是经数控火焰切割后组织应力过大和在过渡圆弧角处存在应力集中。通过采用火焰切割前对底板进行正火处理,提高了材料性能,有效避免了底板的开裂失效。     

家用空调器管路件根部裂漏失效分析

针对家用空调器售后出现管路件根部裂漏问题,对故障件返厂,从工艺设计、金相实验、故障复现等几个方面着手分析,确认根部裂漏原因为设计应力,在空调器生产、运输、运行过程中管路件根部出现裂漏,最终通过对管路件结构进行更改,加强管路件强度,消除应力,未再发生此类故障。     

Crack initiation and propagation induced by inclusions in a nickel-base P/M superalloy under fatigue load

1 IntroductionRecently the key components in advanced aircraftengines are widely made of nickel-base P/M super-alloy. However, non-metallic inclusions are intro-duced into this material during powder metallurgyprocessing. In industry, although many method…     

热处理对Ti-Al-Sn-Zr-Mo-Si-X系合金性能的影响

研究了热处理对3种Ti-Al-Sn-zr-Mo-Si-X（X为ⅤB，ⅥB族一种或几种元素）系合金（A、B、C）室温拉伸性能的影响，对优化合金的热处理制度及优选热处理制度下3种合金的疲劳裂纹扩展行为也进行了探讨。结果表明，优选热处理制度下A、C合金的裂纹扩展速率差别不大，B合金560℃时效处理后，裂纹扩展速率比540℃时效处理的小。在相同热处理制度下，比较3种合金裂纹扩展速率的结果表明，IgΔK在1．2～1．5范围内B合金的抗疲劳裂纹扩展性能较优。