应变速率对中碳低温贝氏体钢强塑性的影响

摘要：为探索低温贝氏体钢的断裂行为,研究应变速率对低温贝氏体钢TRIP效应的影响,采用不同应变速率的拉伸试验对低温贝氏体钢的强塑性进行研究。利用扫描电镜（SEM）、透射电镜（TEM）及X射线衍射（XRD）等试验方法对低温贝氏体钢的微观组织、断口形貌及裂纹走向进行表征。结果表明,随着应变速率的提高,试验钢的屈服强度由771MPa上升至806MPa,抗拉强度由1554MPa上升至1606MPa,断后伸长率由13.5%下降至9.0%。主要原因是高应变速率拉伸引发的绝热温升抑制了残余奥氏体的马氏体相变,对试验钢塑性造成负面影响。     

300M钢腐蚀疲劳裂纹萌生的超载特性

本文对３００Ｍ钢在空气与３．５％ＮａＣｌ溶液中疲劳裂纹萌生的周期超载和单次超载特性进行了试验研究与理论分析。试验结果表明，３．５％ＮａＣｌ溶液中，单次超载所致腐蚀疲劳裂纹迟滞萌生的迟滞强度远小于周期超载的对应值。３．５％ＮａＣｌ溶液与空气中，超载迟滞强度均随超载比增大或等效应力幅水平的提高而增大，在腐蚀疲劳裂纹萌生寿命估算中，只考虑单次超载的迟滞规律，会得出大大保守的寿命估计，只有将单次超载和周期     

CREEP CRACK PROPAGATION IN CONVENTIONAL CAST AND DIRECTIONALLY SOLIDIFIED SUPERALLOY RENE 80

The creep crack propagation in superalloy René80 of two different microstructures,i.e.,equiaxed grain structure by conventional casting and columnar grain by directionalsolidification,was investigated under static load at 1123 K.The creep crack growth rate,da/dt,seems to be correlated with the stress intensity factor,K.The creep crack growth ratein the directionally solidified alloy is lower than that in the conventional cast alloy,owing tothe elimination of transverse grain boundaries.The effect of microstructure on creep crackpropagation has also been discussed.     

晶界碳化物对Fe-Cr15-Ni25合金蠕变裂纹扩展行为的影响SCIEI

在两种不同晶界状态下研究了Fe-Cr15-Ni25合金的蠕变裂纹扩展行为。单相合金的空洞在晶界三叉点处形核,而对晶界上有碳化物析出的合金,空洞在晶界碳化物上形核。晶界碳化物阻碍了空洞的长大和连接,因而大大提高了蠕变裂纹扩展抗力。     

IN-SITU OBSERVATION OF CRACK TIP DEFORMATION IN A DUPLEX STAINLESS STEEL

The development of dislocation structures in the plastic zone ahead of a crack tip has been in-vestigated in a duplex stainless steel during in-situ deformation experiments in a scanningtransmission electron microscope.It was found that the dislocation distribution wassignificantly different in the ferrite and in the austenite.In the ferrite grains,the dislocationsemitted by the crack tip may cross-slip out of the original slip planes and form a broad plasticzone.However,in the austenite,the dislocation free zone is small and the dislocations emittedby the crack pile up in its slip plane.The selection of slip systems at the crack tip depends onthe crack tip Schmid factors in both phases.But after large deformation,the selection of thesecond slip systems at the craek tip in austenite does not depend on the Schmid factors.     

高强度钢腐蚀疲劳裂纹扩展的温度效应和过载迟滞效应

通过在18,35和55℃蒸馏水中疲劳裂纹扩展试验,证明了超高强度钢30CrMnSiNi2A腐蚀疲劳具有强烈的温度效应,得到了ΔK值和温度对裂纹扩展速率影响的复合表达式。由于扩展速率数据拟合得到的表观激活能值(36.7kJ/mol)十分接近于氢在γ-Fe中的扩散激活能值,支持了氢助裂纹扩展的观点。对大气中疲劳裂纹扩展具有重要价值的过载迟滞效应,在腐蚀疲劳时显著地减小,在0.1Hz的低频率下尤其明显。     

热应力作用下碳化钨基钢结硬质合金梯形裂纹的形成机理

在自约束型热疲劳试验机上对碳化钨含量不同的钢结硬质合金进行了热疲劳试验，用金相显微镜和扫描电镜对热疲劳裂纹扩展行为进行了研究。结果表明：在热应力作用下，不仅在合金的表面，在合金的内部都形成了“梯形”裂纹。这种形态的裂纹是由试样缺口处的热疲劳裂纹扩展而引起的，合金中的钢基体相阻碍裂纹扩展，而WC硬质相诱导裂纹扩展，这两种因素的综合作用促使热疲劳裂纹成“梯形”扩展。分析认为：使WC粒子在钢基体中均匀分布，提高钢基体的热疲劳抗力，从而来阻止梯形裂纹的形成，是提高碳化钨钢锆硬质合金抗热疲劳性能的有效途径。     

A fatigue-life prediction methodology for notched aluminum-magnesium alloy in gulf seawater environment

Local-strain and linear-elastic fracture-mechanics (LEFM) methodologies have been investigated for prediction of the corrosion-fatigue life of notched components of specially developed Al-2.5Mg alloys exposed to Arabian Gulf seawater environment. Corrosion-fatigue crack initiation life estimates were obtained using strain-life relationships; corrosion-fatigue crack propagation life estimates were obtained using LEFM relationships. The total corrosion-fatigue life was considered to be the sum of the crack initiation and crack propagation lives. Estimated corrosion-fatigue lives were compared with experimentally obtained corrosion-fatigue life data using center-notched specimens of three types of Al-2.5Mg alloys (containing different amounts of chromium) exposed to Arabian Gulf seawater environment. Two notch geometries, a circular notch (K _t= 2.42) and an elliptical notch (K _t= 4.2), were investigated. Good corrosion-fatigue life predictions can be obtained using local-strain and LEFM methodologies by determining the relevant material constants via a few simple fatigue tests on smooth specimens and a few crack-growth-rate tests in the environment at the frequency of interest.     

冲天炉炉胆的(径向)胀裂问题及其防止措施

冲天炉炉胆径向胀裂问题，也是一道颇有难度的课题，本文提出：用平行四边形、竖立的梯形和微凹矩形三种炉壁断面作为防止措施。     

角接接头焊缝外观检查质量标准的探讨

针对厚壁管角接接头多次出现裂缝,解剖后又没有发现足以引起裂缝的除未焊透外的其它焊接缺陷的情况,认为除应力集中外,角接接头本身的强度也是决定是否会开裂的一个重要原因,为此建立了一个数学模型,同时结合实例证明.按目前大多数人认可的角接接头焊脚的定义,根据DL/T869-2004<火力发电厂焊接技术规程>去控制焊接尺寸,会出现焊缝有效厚度不足的问题.从而根据角接接头有效厚度不应小于最小壁厚的观点,提出对此类角接接头焊缝外观质量控制的几点意见.