压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

Development of ultra light magnesium-lithium alloys

Magnesium-lithium alloys are among the lowest density metallic materials. Addition of lithium, with a relative density of 0·53, in magnesium reduces the density of the alloy significantly. Furthermore, addition of nearly 11 wt.% lithium converts hexagonal close packed structure of pure magnesium to a body centered cubic lattice, markedly improving formability of the alloy. The development of these alloys, however, had been hampered due to the high reactivity of lithium and magnesium in the molten state and also, due to poor creep resistance and instability of mechanical properties at room temperature. In an attempt to indigenize these ultra light alloys for possible applications in Indian satellite programme, detailed research work was initiated in DMRL. The difficulties associated with producing sound cast ingots have been overcome by controlling melting and casting parameters of these alloys. Extensive work has been done on structure-property correlation of alloys with varying lithium content and minor alloying additions. Based on these work, advanced magnesium-lithium alloys have been developed with improved tensile properties, room temperature stability and creep resistance. Wrought products (plates/sheets) of magnesium-lithium alloy have been supplied to ISAC, Bangalore and are being used in their INSAT-2 programme. This paper describes the systematic studies carried out in the laboratory to indigenize these ultra light alloys.     

K0.9Li0.1（Ta0.5Nb0.5）O3晶体压电应变系数的测量

用准静态ｄ＿（３３）测量仪和干涉法相结合。测量了Ｋ＿（０．９）Ｌｉ＿（０．１）（Ｔａ＿（０．５）Ｎｂ＿（０．５）Ｎｂ＿（０．５））Ｏ＿３晶体的压电应变系数。结果为：ｄ＿（３３）＝８６．０，ｄ＿（３３）＝一２９．５，ｄ＿（１５）＝１１２．９×１０￣（－１２）Ｃ／Ｎ．     

甲醇蒸汽转化炉炉管损伤分析及修复

通过对乙烯厂甲醇车间蒸汽转化炉炉管的材料成分、力学性能、金相组织等的分析，确定定其失效模式为高温蠕变损伤，找到造成及影响炉管失效的主要因素。并对炉管的修复以及预防提出了有效的方法及建议。     

钇铝榴石晶体的超高温强度和流变性

在温度高达２０２３Ｋ，可控氧分和不同应变速率条件下，对钇铝榴石晶体进行了蠕变实验，研究表明，钇铝榴石晶体的脆－延性转变温度高达１８３３Ｋ，在温度低于２０２３Ｋ和应变速率大于１０＾－５．ｓ＾－１的条件下，其蠕变流动强度高于３０００ＭＰｑ对钇铝榴石晶体蠕变机制的研究表明，其高温塑性变形起因于晶体的位错滑移，晶体在高温下的高强度与其很高的Ｐｅｉｅｒｉｓ力相关，钇铝榴石晶体在高温晶体稳定性和超高强度使其菜     

Analytical solution for the axisymmetric plane strain electroelastic dynamics of a special non-homogeneous piezoelectric hollow cylinder

By virtue of the introduction of a dependent variable and the separation of variables technique, the axisymmetric plane strain electroelastic dynamic problem of a special non-homogeneous piezoelectric hollow cylinder is transformed to a Volterra integral equation of the second kind about a function with respect to time, which can be solved successfully by means of the interpolation method. Then the solutions of displacements, stresses, electric displacements and electric potential are obtained. The present method is suitable for a piezoelectric hollow cylinder with an arbitrary thickness subjected to arbitrary mechanical and electrical loads. Numerical results are finally presented.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

Procedures for analysis of strain transfer in the acetabular region in vitro

The failure of acetabular cups via loosening, migration or fracture is partially related to the stress distribution existing in the acetabular region. The complexity of the investigation of these stresses demands the application of a variety of model testing techniques involving combined embedded strain gauging, finite element analysis, transmission and reflective photoelasticity and crack propagation studies. The application of these procedures are described and the difficulties of obtaining representative loadings and restraints are commented upon.     

Temperature–stress–strain trajectory modelling during thermo-mechanical fatigue

The isothermal strain‐life approach is the most commonly used approach for determining fatigue damage, particularly when yielding occurs. Computationally it is extremely fast and generally requires elastic finite element analyses only. Therefore, it has been adapted for variable temperatures. Local temperature—stress–strain behaviour is modelled with an operator of the Prandtl type. The hysteresis loops are supposed to be stabilized and no creep is considered. The consequences of reversal point filtering are analysed. The approach is finally compared to several thermo‐mechanical fatigue tests and the Skelton model.