Influences of temperature and Sn-addition on microstructural evolution of Ag during FSW

ABSTRACT

The microstructural evolutions of pure Ag and Ag-0.75 wt-%Sn during rapid cooling friction stir welding (FSW) were examined. At the lower welding temperature of FSW conditions, the annealing twinning was highly suppressed and the microstructural evolution was dominated by the discontinuous dynamic recrystallisation (DDRX) via the high angle boundary (HAB) bulging. The fully recrystallised microstructure was remarkably finer than that formed through the frequent annealing twinning at the higher welding temperature. Moreover, the Sn-addition caused the HAB bulging due to the inhibition of dynamic recovery and decreased mobility of grain boundaries. With decreasing the ratio of the peak temperature to the recrystallisation temperature, the dominant grain refinement mechanism is implied to change from the annealing twinning to the DDRX.     

Experimental Study of Microstructure Evolution during Tempering of Quenched Steel and Its Application

LARGE-SIZED FORGINGS are usually intensivelyquenched to obtain the desired microstructuredistribution,high strength and hardness.Becauseresidual stresses are high in quenched large-sizedforgings,tempering processes follow quenchingprocesses to reduce the residual stress and obtain goodmechanical properties.Several differentmicrostructures are generated in quenched steelforgings,such as martensite,bainite and retainedaustenite.Modeling of microstructure evolution inquenched steel during …     

COMPUTERIZED SIMULATION OF MOLTEN SALT SOLUTION OF Li,KF,Cl SYSTEM BY MOLECULAR DYNAMIC METHOD

The structure and properties of molten salt solution o J Li,K|F,Cl system have been investigedby computerized simulation of molecular dynamic method.The partial RDF,the partial molarenergy of mixing and the diffusion coeffients of Li~+,K~+,F~- and Cl~- have been calculated.The results are in agreement with the experimental values.The regularities of the distributionof ions and mieroscopic holes are discussed based on the results of computerized simulation.     

304不锈钢在高温水中的应力腐蚀破裂SCIEI

采用U型弯曲法应力腐蚀破裂试验、电化学测量以及Auger电子能谱(AES)分析方法研究了温度、氯离子浓度和溶解氧含量在高温水中对304不锈钢的应力腐蚀破坏(SC)敏感性的影响及其与表面膜之间的关系。在空气饱和的高温水中(溶解氧为8ppm),随着温度的升高(200—300℃)或氯离子浓度的降低(500—20ppm)304钢SCC敏感性降低。文中还讨论了氧化膜在SCC萌生和扩展中的作用。     

爆炸焊接有效多方指数γ及可焊窗口

基于对爆炸焊接复板运动形态的基本假定及爆炸气体动力学方程建立冲击波方程，将爆炸气体的作用视作固壁(基板)的正反射，建立运动冲波方程，根据现有的研究成果资料及爆炸焊接理论指导工程实践中存在的问题，从而推导出有效多方指数γ的限定使用范围，为金属爆炸焊接工程应用的参数计算提供可靠依据。以铝材作复板，低碳钢作基板以此作为金属爆炸焊试件，分别使用2号岩石硝铵炸药、泰乳炸药和梯恩梯炸药，利用列契脱飞板运动公式，可以计算出复板厚度与炸药厚度的近似关系式。     

1Cr20Co6Ni2WMoV钢热变形行为研究

文章采用Gleeble-2000热模拟试验机对1Cr20Co6Ni2WMoV热强钢的热变形行为进行研究。变形温度为950℃,1000℃,1050℃,1100℃,1160℃,变形速率为0．01s~(-1),0．1s~(-1),1s~(-1),10s~(-1)。结果表明．1Cr20Co6Ni2WMoV钢在低应变速率热压缩变形过程中发生明显的动态再结晶;当应变速率大于10s~(-1)时,只发生动态回复。动态再结晶晶粒随变形温度降低,应变速率升高而减小。随应变速率的提高,峰值应力和峰值应变均升高。     

数控机床位置伺服在线调试与动态性能分析研究

介绍一种在数控机床位置伺服系统在线调试中应用系统动态性能分析方法的基本原理，给出了一种位置伺服系统动态响应曲线、动态性能分析及其主要技术指标的实例。     

陶瓷与金属扩散连接的研究现状

陶瓷与金属的连接技术是材料工程领域的热点研究课题,而扩散连接方法被认为是陶瓷与金属连接最适宜的方法。本文综述了陶瓷与金属扩散连接的研究现状,重点介绍了界面反应研究、残余应力分析和连接工艺研究等内容,并在此基础上指出了研究中所存在的问题。     

焊接工艺过程对中厚板埋弧焊应力场影响的数值模拟

通过ANSYS有限元分析软件,采用热-应力直接耦合分析法对低碳钢中厚板埋弧焊焊接温度场与应力场进行了模拟分析,并比较了单面双层焊、正反双面依次焊和正反双面同时焊三种焊接工艺过程对接头焊接残余应力的影响。     

Theoretical study and numerical simulation of the stress fields of the Al2O3 joints brazed with composite filler materials

Non-linear finite element code MSC. Marc was utilized to analysis the field of stress of the Al2O3 joints brazed with composite filler materials. The properties of the filler materials were defined by using the mixing law, method of Mori-Tanaka and theory of Eshelby to ensure the accuracy and reliability of results of finite element method （FEM）. The results show stress in brazed beam is higher than that in base material. The maximal stress can be found in the interface of joint. And the experimental results show that the shear strength of joints increases from 93.75 MPa （ Al2O3p Ovol. % ） to 135.32 MPa （ Al2O3p 15vol. % ） when composition of titanium is 3wt% in the filler metal.