国有公路运输企业改革创效的现实选择

通过对公路运输企业经营实践的考察 ,介绍了国有公路运输企业改革创效的一些现实选择 ,以供运输公司经营借鉴 ,从而摆脱困境 ,取得良好业绩     

Impact of the addition of an enzyme pool on an activated sludge system treating dairy wastewater under fat shock loads

BACKGROUND: The application of lipase‐rich enzyme pools (such as the crude solid enzymatic preparation (SEP) obtained from Penicillium restrictum solid‐state fermentation of agro‐industrial wastes) to activated sludge systems may be an effective strategy for preventing various operational problems. The continuous addition of SEP to the treatment system can become cost‐prohibitive when in situ production and/or storage are factored in. The application of SEP to high‐fat wastewater treatment would only be justified as an emergency measure, such as a sudden increase in the fat content of the bioreactor influent. Therefore, the primary objective of this work was to investigate the efficiency of a crude SEP during fat shock loads, simulated through the periodic addition of dairy industry waste containing high fat concentrations to the feed stock of an activated sludge system, operated in continuous mode. RESULTS: The test bioreactor exhibited a higher average chemical oxygen demand (COD) removal efficiency than the control bioreactor (83% for control and 90% for test) and the fat accumulation in the biological flocs of the test bioreactor was 3.2 times lower than that in the control bioreactor. Turbidity was also lower in the effluent of the test bioreactor (123 and 66 FTU in control and test, respectively) and it had a shorter recovery time between shock loads, especially when the interval between loads was shorter than one month (biweekly and weekly shock loads). CONCLUSION: The addition of SEP during fat overloads in the reactor feed maintained efficient COD removal in the test bioreactor for 270 days without any operational problems. Copyright © 2008 Society of Chemical Industry     

欠驱动系统Pendubot的模糊控制策略

本文针对欠驱动Pendubot机器人系统，提出一种简单可靠的摇起及平衡控制策略。通过利用模糊控制及全状态反馈控制技术来分别设计摇起控制器及平衡控制器，其中模糊摇起控制器的设计使得系统的摇起可靠性得到大大的加强，并缩短了响应时间，两个控制器的转换通过转换装置实现。最后的仿真结果验证了算法的有效性。     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Measurement of specimen charging in scanning electron microscopy with a kelvin probe

A vibrating Kelvin probe in form of a platinum wire loop is used to measure the surface potential U_s on electron-irradiated free-floating metal and insulator specimens as a function of electron energy E. This allows an accurate measurement of the critical electron energy E₂ for no charging. At energies below E₂, the positive charging increases with decreasing energy to U_s=2–5 eV at E=0.5 keV and switching off the collector bias of the Everhart-Thornley detector. A two-to threefold increase of U_s is observed when the bias is switched on. For E > E₂, the strong increase of a negative surface potential can be measured. Insulating films free-supported on a conductive substrate show a steep decrease to small positive and negative U_s when the film thickness becomes lower than the electron range at a critical energy E₃ > E₂. At insulating specimen the temporal decrease of charging can be measured when the electron beam is switched off.     

多台并行随机CIMS可靠性的扩散估计界

ＣＩＭＳ可靠性模型随机研究的突出特点是工作站的并行结构使系统的状态个数呈现指数级增大，同时，并行结构与有限的缓冲库相互交织在一起，这使系统状态呈爆炸趋势，显然，对系统作精确的分析与系统呈现的状态爆炸趋势构成了难以解决的矛盾，如何解决这一矛盾正是ＣＩＭＳ随机理论有待开发的重要课题。我们把扩散近似方法引入到多台并行的ＣＩＭＳ可靠性模型中，以简单的连续过程描述了具有状态爆炸趋势的复杂离散过程，给出了ＣＩ     

受控离散事件过程（CDEP）的一种代数分析方法

本文在文［１～３］的基础上，提出了受控离散事件过程（ＣＤＥＰ）的一种代数分析方法，弥补了Ｒａｍａｄｇｅ和Ｗｏｎｈａｍ［１～３］的理论对具体系统的应用缺乏可操作性的缺陷，使得对ＣＤＥＰ动态过程的分析变得更为直观，同时也使控制器的设计过程更具可操作性．     

给定拓扑结构的网络的可靠性设计

本文首先讨论了网络链路堵概率的加权平均值，提出了网络分配的一般准则，并在考虑了网络链路生存链路概率的因素后，提出了更一般的网络链路堵塞概率的加权平均值，以此为基础，分别讨论了网络在给定点的费用条件下，使得网络可靠性最大的网络设计问题，以及在给定网络可靠性指标的前提下，使得网络费用最小的网络设计问题。